हिंदी Call90310 74624
Home›Tiles›Vitrified vs ceramic
Tile comparison

Vitrified vs ceramic tiles: the difference, and which goes where

The short answer
  • Vitrified on every floor you live on: rooms, kitchen, passage, stairs, outside.
  • Ceramic on bathroom and kitchen walls, and 300×300 matt on a small bathroom floor.
  • Never a ceramic wall tile on any floor.

The difference is inside the tile, not on its face. Ceramic has an open, thirsty body under a glaze. Vitrified is fired until the body turns glassy and dense. Ceramic costs less per square foot, which is why it belongs on walls, where nobody walks.

15% vs 0.08%
Water it soaks upCeramic wall tile against glazed vitrified, both Birla Pivot.
2½–5×
Load before it breaks1,500 N for vitrified, 300–600 N for a wall tile.
Mohs 3
Glossy is not harderA glossy vitrified face scratches like a wall tile. Matt vitrified: 5.
Cut a tile in half and look
Cross-section of a ceramic wall tile and a glazed vitrified tile The ceramic tile has a thin glaze over a porous clay body; water enters from the back. The vitrified tile has a printed glaze over a dense glassy body; water sits on it in drops. Water absorption: ceramic about 15 percent, vitrified 0.08 percent or less, too small to see on the same scale. CERAMIC WALL TILE 7.5 mm · 300×450 Glaze on the face: the only part that keeps water out Body: open, porous fired clay. Water goes in from the back. WATER IT SOAKS UP (LAB TEST) 15 ± 3 % GLAZED VITRIFIED TILE 8 mm · 600×600 Body fired till it turns glassy: pores closed Water stays on top. Strength is in the whole body. 0.08 % or less: a hairline
Drawn many times thicker than real. Both bars on the same scale. Figures: Birla Pivot technical sheets for digital wall tiles and for GVT/PGVT, catalogue printed pages 61–64.
Side by side

Vitrified vs ceramic, figure by figure

Every number below is from the maker of the tiles we sell, Birla Pivot, as printed in its technical sheets. Shop talk says "vitrified is stronger"; this is how much stronger.

CeramicVitrified
BodyFired clay, open and porous, under a glazeFired until glassy, dense, pores closed
Group in the tile standard (ISO 13006)BIIIwater absorption above 10%BIawater absorption 0.5% or less
Water it soaks up15 ± 3%Pivot wall tiles, typical≤ 0.08%Pivot GVT, average
Bending strength18 N/mm²average40 N/mm²average; 38 any single tile
Breaking load, minimum300–600 N300 N at 7.5 mm or thinner, 600 N above. Ours are 7.5 mm, so read 300.1,500 NGVT and PGVT
Scratch hardness (Mohs)35 matt · 3 glossy/polisheddouble charge: 5
Surface wear classNot given (wall tile)Class V matt · Class III polished
Thickness7.5 mm300×450 and 300×3008 mm 600×600 · 8.2 mm 600×1200
Weight per sq ft1.2 kg10.5 kg box, 8.72 sq ft1.7 kg26.5 kg box, 15.5 sq ft
Sizes Birla Pivot makes300×300, 300×450, 300×600600×600, 600×1200, 800×1600, 1200×1800; planks; full body up to 800×3000
Sizes on our shelf300×450 wall, 300×300 floor2x2, 2x4, 200×1200 planks, 400×400 outdoor
FinishGlossy or matt glaze, wall designs in seriesMatt, glossy, high gloss, polished, rustic
Where it goesBathroom and kitchen walls; 300×300 on small wet floorsEvery floor; outdoor grades for terrace and parking
PriceLower per sq ftHigher per sq ft

Wall-tile figures are Birla Pivot's "typical values for wall tiles"; vitrified figures are its "our value" for glazed vitrified (GVT) and polished glazed vitrified (PGVT). Pivot sells the 300×300 floor tile in the same ceramic range and box table as its wall tiles and prints no separate strength figures for it. Any size we don't keep, we can order for you; ask on WhatsApp for the time it takes. Today's prices: tiles rate.

What the numbers mean in your house

Two litres against one spoon

Percentages are hard to picture. Here are the same figures per square metre of tile, worked out from Birla Pivot's own box weights.

Water soaked up per square metre of tile One square metre of ceramic wall tile weighs about 13 kg and can soak up about 2 litres of water in the lab test. One square metre of glazed vitrified tile weighs about 18.4 kg and soaks up 15 millilitres or less, about one tablespoon. 2 L1.5 L1 L0.5 L CERAMIC WALL TILE about 2 litres GLAZED VITRIFIED ≤ 1 spoon 15 ml or less PER SQUARE METRE OF TILE
Worked out from Birla Pivot's sheets: ceramic 10.5 kg per 0.81 m² box × 15% water; vitrified 26.5 kg per 1.44 m² box × 0.08%. The lab test boils the tile, so real walls take in less, but the gap is the same.

1On a wall, the thirst helps

The glaze faces the room and keeps water out. The porous back drinks in the cement slurry and holds on. Nobody walks on a wall, so its lower strength never matters. That is why ceramic is the right, cheaper choice for bathroom and kitchen walls.

2On a floor, it fails

A floor takes feet, a dragged almirah, a dropped steel bucket. A wall tile is rated for 300–600 N of load; Pivot's vitrified for at least 1,500 N. Once the glaze is chipped, water and dirt soak into the open body and the stain stays.

3Shine is not strength

Pivot gives its glossy and polished vitrified a surface hardness of Mohs 3, the same as a wall tile; matt vitrified gets 5. The vitrified body is far stronger, but a glossy face still shows scratches from grit under shoes. On a busy floor, matt or double charge wears better.

Porcelain, GVT, PGVT, double charge

Most of the names in a tile shop are one family

There are really two kinds, set by how much water the body takes in. Every other name is a kind of vitrified tile with a different face.

Tile family tree Fired clay tiles split into two groups. Ceramic, ISO group BIII, water above 10 percent: wall tiles and 300 by 300 floor tiles. Vitrified family, ISO group BIa, water 0.5 percent or less: glazed vitrified, polished glazed vitrified, double charge, soluble salt, full body, porcelain and outdoor parking tiles. Stars mark what we keep in stock. FIRED CLAY TILES CERAMIC Group BIII water above 10% ★ Wall 300×450bath, kitchen walls ★ Floor 300×300small bathroom floor Wall 300×600we can order it VITRIFIED FAMILY Group BIa water 0.5% or less ★ GVT, glazed vitrifiedprinted glaze: 2x2, 2x4, planks PGVT, polished GVTGVT polished to a mirror shine ★ Double chargecolour pressed deep in ★ Soluble saltcolour soaked into the surface Full body · Porcelainone colour right through ★ Outdoor / parking ★ = on our shelf
Groups as printed on Birla Pivot's technical sheets (ISO 13006). Product names from its catalogue range page.

Porcelain is vitrified under another name

Many buyers ask whether porcelain is a third kind, better than both. In the tile standard it sits in the same group as vitrified, BIa, with water absorption of 0.5% or less. Birla Pivot lists "Porcelain" as one line in the same range as its GVT and double charge. Don't pay extra for the word. Ask for the water absorption figure on the sheet.

  • GVT (glazed vitrified): a vitrified body with a printed glaze on top, so it can look like marble or wood. All our 2x2, 2x4 and planks are GVT.
  • PGVT: the same tile, polished to a mirror shine. It looks best in a drawing room, but Pivot's sheet gives the polished face only Mohs 3 and wear class III.
  • Double charge: two layers of colour are pressed into the body, so wear doesn't show the way it does on a print. Pivot's sheet: deep-abrasion loss 140 mm³ at most, Mohs 5. For a shop, passage or busy kitchen: double charge.
  • Outdoor 400×400: Pivot's parking tile, 11.8 mm thick with a rough face. Its sheet: water under 0.5%, Mohs 6, at least 1,800 N for the 10 mm tile. See outdoor tiles.

Basics in Hindi: vitrified tiles kya hota hai. Reading the box: tile PEI and water absorption.

Which room gets which

A typical house, tiled the right way

Most houses in Muzaffarpur end up with both: vitrified across the floors, ceramic on the walls of the wet rooms. That split is right. The floors are where the area and the load are.

House plan showing which tile goes in each room Porch and aangan in outdoor anti-skid tile. Drawing room in 2x4 glazed vitrified. Bedroom in wooden-look planks. Second bedroom in 2x2 glazed vitrified. Kitchen floor in matt 2x2 vitrified with ceramic tiles on the wall above the platform. Passage in double charge. Bathroom walls in ceramic 300 by 450, bathroom floor in 300 by 300 matt. Stairs in matt vitrified. Porch, aangan · outdoor 400×400 Drawing room2x4 vitrified Bedroomwood-look planks Kitchenmatt 2x2 vitrified platform Passagedouble charge Bathroom300×300 matt floor Bedroom 22x2 vitrified Stairsmatt vitrified
Vitrified floor Ceramic 300×300 floor Ceramic wall tiles 300×450 Outdoor tile
Red lines are walls that get ceramic tiles: the bathroom to door height or ceiling, the kitchen wall above the platform.
PlaceTileWhy
Drawing room, bedrooms2x2 or 2x4 GVT, or planksFurniture, feet, daily mopping
Passage, shop frontDouble charge or matt GVTMost feet, grit from outside
Kitchen floorMatt 2x2 GVT or double chargeOil and water make glossy slippery
Kitchen wall above platformCeramic 300×450No load, wipes clean, costs less
Bathroom wallsCeramic 300×450 seriesWall only; fits round taps and pipes
Bathroom floor300×300 matt or matt vitrifiedSmall tiles follow the slope to the drain; matt grips
StairsMatt vitrifiedA glossy edge is where people slip
Terrace, porch, parkingOutdoor 400×400Sun, rain, scooters; rough face
Any floorCeramic wall tileNever: thin, porous, rated 300–600 N

Room by room with designs: kaun sa tiles kahan. Why a wall tile cracks on a floor: wall tile floor par kyun nahi.

What goes wrong

Four mistakes we see on sites

Wall tile laid on a floor

You see: cracks under furniture, chipped corners at doors

The design matched, so it went on the floor. A wall tile is 7.5 mm and rated 300–600 N. Once a corner chips, the porous body under it stains.

Glossy tile on a wet floor

You see: slips in the bathroom and by the kitchen sink

Being vitrified doesn't make a tile safe when wet. Take matt, or anti-skid, wherever water stands.

Indoor tile on the terrace

You see: a glassy, slippery terrace every monsoon

Outside needs Pivot's outdoor tile: 11.8 mm thick, a rough face, Mohs 6. A polished indoor GVT is the wrong tile there.

= ≠

Choosing by the shine

You see: a "vitrified" price paid for a ceramic tile

From across the shop, a glossy ceramic and a glossy vitrified look the same. Turn them over, and read the box.

In the shop

How to tell them apart in one minute

These are usual shop checks, not lab tests, but together they don't lie.

ceramic back vitrified back

1. Turn it over

A ceramic back is usually reddish or buff, rough, and ribbed. A vitrified back is fine, even, and grey or off-white, close to the colour of the broken edge.

soaks in, dark patch stays as a drop

2. A drop of water on the back

On ceramic it disappears in seconds and leaves a dark patch: that is the 15%. On vitrified it sits there as a drop.

1.2 kg 1.7 kg per sq ft, from the box

3. Read the box

The box prints the sq ft and the weight. Pivot's ceramic weighs about 1.2 kg per sq ft and its vitrified about 1.7 kg, almost a third heavier for nearly the same thickness. The box or bill also says "GVT", "PGVT" or "wall".

Price

Ceramic costs less, but compare per square foot

Tiles are sold by the box, and boxes hold different areas. A 300×450 box covers 8.72 sq ft, a 2x2 box 15.5 sq ft. Comparing box prices makes ceramic look even cheaper than it is.

TileIn a boxPer boxPer sq ft
Ceramic wall 300×4507.5 mm6 · 8.72 sq ftAsk rateAsk rate
Ceramic floor 300×3007.5 mm8 · 7.75 sq ftAsk rateAsk rate
GVT 2x2, 600×6008 mm4 · 15.5 sq ftAsk rateAsk rate
GVT 2x4, 600×12008.2 mm2 · 15.5 sq ftAsk rateAsk rate
Double charge 600×6008 mm4 · 15.5 sq ftAsk rateAsk rate
Plank 200×12005 · 12.91 sq ftAsk rateAsk rate
Outdoor 400×40011.8 mm5 · 8.61 sq ftAsk rateAsk rate

Box contents from Birla Pivot's catalogue packing tables. Prices for every design, updated daily: tiles rate. Laying, cutting and delivery are charged separately; see delivery. Boxes for your rooms: tiles calculator.

Where the money goes: in a whole house, the floor area is several times the tiled wall area, so the floor tile decides the bill. Saving there with a wall tile is the one saving that costs more later. Spend on the floors, save on the walls.

Questions people ask us

Short answers

Which is better, vitrified or ceramic?

For floors, vitrified. Birla Pivot's glazed vitrified soaks up 0.08% water or less and takes at least 1,500 N before it breaks; its ceramic wall tiles soak up about 15% and are rated 300–600 N. For bathroom and kitchen walls, ceramic does the job at a lower price.

Vitrified aur ceramic tiles mein kya antar hai?

Body ka. Vitrified ki body kaanch jaisi ghani hoti hai, paani lagbhag nahi sokhti aur kahin zyada majboot hoti hai, isliye har farsh par lagti hai. Ceramic ki body chhidradar hoti hai aur sasti hoti hai; bathroom aur kitchen ki deewar ke liye theek hai. Poora Hindi page: यहाँ पढ़ें.

Can ceramic tiles go on the floor?

Only a ceramic floor tile, like our 300×300 matt, on a small floor that few people walk on, such as a bathroom. A ceramic wall tile must never go on any floor.

Is porcelain better than vitrified?

They are the same family. Both sit in Group BIa of the tile standard, with water absorption of 0.5% or less. Compare the figures on the sheet, not the name.

Vitrified or ceramic for the bathroom?

Ceramic 300×450 on the walls. On the floor, 300×300 matt ceramic or a matt vitrified tile. No glossy tile on a wet floor, whatever it is made of.

Is glossy vitrified harder than matt?

No, the other way round. Birla Pivot gives its matt GVT a surface hardness of Mohs 5 and wear class V; glossy and polished get Mohs 3 and class III. Glossy looks richer but shows scratches sooner on a busy floor.

Why are vitrified tiles costlier?

Finer raw material, a hotter and longer firing, and bigger sizes. Per square foot, ceramic is cheaper. Today's price for each design is on the tiles rate page.

Can ceramic go outside, on a terrace or parapet?

Not on a terrace floor. Outside, water gets into a porous body, and sun and rain work on it. Use Pivot's outdoor 400×400, which its sheet rates for 100 freeze-thaw cycles and at least 1,800 N.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Looks after paint, putty, tiles and waterproofing at our Reva Road store, Muzaffarpur. Every figure on this page was read from Birla Pivot's own technical sheets on 12 Nov 2026. Where a figure depends on thickness, the page gives the lower, safer one.

Where the numbers come from

  1. Birla Pivot, Tiles consolidated catalogue, printed pages 61–62, "GVT & PGVT technical details": water absorption average ≤ 0.08%, modulus of rupture average 40 (single tile 38) N/mm², breaking strength min. 1,500 N, Mohs 5 matt / 3 polished, abrasion class V matt / III polished; packing 600×600 8 mm, 4 tiles, 15.5 sq ft, 26.5 kg; 600×1200 8.2 mm, 2 tiles, 15.5 sq ft.
  2. Same catalogue, pages 61–62, "Double charge & soluble salt technical details": water ≤ 0.08%, min. 1,300 N, Mohs 5, deep abrasion max. 140 mm³; 600×600 8 mm, 4 tiles, 15.5 sq ft, 24.5 kg.
  3. Same catalogue, pages 63–64, "Digital wall tiles technical details" (ISO 13006 Group BIII, E > 10%): typical water absorption 15 ± 3%, modulus of rupture average 18 N/mm², breaking strength min. 300 N at ≤ 7.5 mm and 600 N above, Mohs 3; ceramic wall and floor packing 300×450 7.5 mm, 6 tiles, 8.72 sq ft, 10.5 kg; 300×300 7.5 mm, 8 tiles, 7.75 sq ft.
  4. Same catalogue, pages 63–64, "Parking tiles technical details" (Group BIa): water < 0.5%, min. 1,800 N (10 mm), Mohs 6, frost 100 cycles; 400×400 11.8 mm, 5 tiles, 8.61 sq ft.
  5. Same catalogue, "Product range" page: sizes made for GVT/PGVT, full body, double charge, parking and digital wall tiles. Birla Pivot private-label brochure: range list including Porcelain.

Send us your room list

Tell us the rooms and sizes. We'll send back which tile goes where and the boxes for each, with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com