हिंदी Call90310 74624
Home›Tiles›Bathroom floor
Tiles guide · wet floors

Anti-skid tiles: which tile does not slip, for bathroom, terrace, parking and elderly parents

The short answer
  1. Matt or rough face
  2. Small tile
  3. Every joint filled
  4. Floor falls to the drain

For anything that gets wet, take a matt or rough-faced tile and never a glossy one. In the bathroom that means a 300×300 matt tile such as 393 matt. For the open terrace, parking and gate path, use the 400×400 outdoor tile.

0.6
Wet COF to look forThe grip number Johnson quotes for a shower floor. US makers accept 0.42 as a bare minimum; we go with the higher one.
R10–R11
Ramp class, home bathroomVilleroy & Boch's advice. Our tiles show no such class on paper; read "What our boxes say" below.
6.7 m
Joint in every sq m of 300×300Against 3.3 m with 600×600. More edges for the foot to catch.
Why a matt face holds a wet foot
Why a matt face grips when wetTwo cross-sections of a wet floor. On a smooth glaze a film of water sits between the foot and the tile and the foot slides. On a matt or rough face the foot rests on the tiny peaks and the water collects in the valleys. GLOSSY GLAZE, WET bare foot foot slides A smooth film of water carries the foot. MATT OR ROUGH FACE, WET bare foot The peaks carry the foot. The water sits in the valleys.
Not to scale: the roughness is drawn many times larger than it is. The yellow dots are where the sole touches the tile.
Three things decide it

How a floor grips, and what you can control

A fall in a bathroom is a wet foot on a smooth surface. Three choices change that, and you make all three before the tiler arrives.

1. The face of the tile

A glossy glaze is a sheet of glass. Soap and water turn it into a skating surface. A matt or rough face has tiny peaks that hold the foot while the water runs into the valleys. This is the biggest factor, and it costs you nothing to choose.

2. The size of the tile

Every joint is an edge for the foot to catch, and a small tile has more of them: 6.7 m of joint per sq m at 300×300, 3.3 m at 600×600. Small tiles also follow the fall to a drain, where big ones leave puddles or need awkward cuts. Joints help only if they are filled; an empty joint just collects dirt.

3. The water and the fall

Standing water makes any tile worse. A floor that falls gently to the drain stays thin-wet and dries sooner. Soap scum builds up on any tile, so wash it off.

Joints in one square metre
Joint length in each square metre of floorThree one-metre squares of floor with tile joints drawn in red: 300 by 300 tiles give 6.7 metres of joint, 400 by 400 give 5, and 600 by 600 give 3.3.300×3006.7 msmallest tile we advise for a shower400×4005.0 mour outdoor tile600×6003.3 ma hall tile (2x2)
Counted from the tile size, joint width ignored. A calculation, not a maker's figure.
What the numbers mean

Reading a slip rating, and what we can and cannot tell you

Brands use different scales for the same idea. They are not interchangeable, so here they are side by side.

Four ways of saying how much grip a tile hasA friction scale from 0 to 1 with marks at 0.42 and 0.6; the R9 to R13 ramp classes with R10 and R11 marked; the barefoot classes A, B and C; and a dashed box for the R1 on our outdoor tile names, which has no test number behind it.COF, wetA friction number. Higher grips more.01.00.420.6US minimumour floorR classShoes and oil on a tilting ramp.R9R10R11R12R13R10–R11: usual advice for a home bathroomBarefoot classBare feet and water on a ramp.A12°B18°C24°Higher letter = steeper slope before slippingPivot "R1"On our outdoor tile names.Pivot's own label. No test number given, so we don't rate it.
COF 0.6: H&R Johnson's bathroom FAQ, also used by Houzz India's bathroom guide. 0.42: US tile standard as quoted by US makers. R9–R13 and A–C: German test methods, now inside EN 16165 (DGUV). R10–R11: Villeroy & Boch. Sources differ on the lower edge of each R class, so no angles are shown for R.

COF: the friction number

The coefficient of friction compares how hard it is to slide a foot over the tile with how hard the foot presses down. Ask for the wet figure; dry numbers flatter every tile. Where makers disagree, we use the higher figure, 0.6.

R9 to R13: the ramp class

A tester in shoes walks on oil over a tilting ramp; the steeper the ramp before slipping, the higher the class. It is built for workplaces. For bare wet feet there is a second test with classes A, B and C.

What our boxes say Birla Pivot's catalogue prints no slip-test number beside our bathroom floor tiles, and the two outdoor tiles carry only "R1" in their bill names. R1 is Pivot's own label: some other heavy-duty designs in the same catalogue are marked R2 to R4, but the catalogue explains none of it. We will not turn R1 into a COF or an R class. If you need a tested number, for a public bath or a parent who has already fallen, tell us and we will ask Birla Pivot for its test report in writing. Until we hold it, we describe the finish and show you the piece.
Our anti-skid tiles

Which of our tiles goes where

We sell genuine Birla Pivot tiles with a GST bill. Every one below can be ordered; the price is per box, today's figure on the tile rates page.

Birla Pivot's catalogue lists the 400×400 range as heavy-duty outdoor tiles for loads, traffic areas and large vehicles. The 1145 and 1217 floor tiles are also 300×300 bathroom pieces; turn the piece over in your hand in the store, and use it on the shower side only if the face is matt.

PlacePickWhy
Shower side of the bathroom393 matt or Satvariyo-08 floor, 300×300Matt face, small tile, many joints. See bathroom floor tiles.
Dry side of the bathroomAny floor tileBut wet feet drip onto it. For an elderly person, run the matt tile across the whole floor.
Terrace walkway, verandah, aanganSasa Beige or Hexa Grey, 400×400Rough outdoor face that grips in rain. See outdoor 400×400.
ParkingSasa Beige or Hexa Grey, 400×400Built as heavy-duty outdoor tile. See parking tiles.
StairsA matt tile; the edge matters mostSee stair tiles.
Balcony, wash area393 matt if covered; an outdoor tile if open to rainA covered balcony behaves like a bathroom. An open one needs the rough outdoor face.
Grip also depends on the laying

Laying a bathroom floor so water leaves

A matt tile on a floor that holds a puddle is only half a fix. The fall and the waterproofing decide how wet the tile stays.

Plan: fall to the drain
A bathroom floor made to grip and drainPlan of a 5 by 7 foot bathroom. The dry side on the left may have any floor tile. The shower side on the right has matt 300 by 300 tiles and the floor falls from all four sides to a drain at the low point. door DRY SIDE SHOWER SIDE any floor tile matt, 300×300 drain each square is one 300×300 tile (about 1 ft) Floor falls gently from every side to the drain
Red arrows show the fall. The dashed line is where matt tile is a must; on the other side it is your choice.
What is under the tile
Layers under a bathroom floor tileSide view from the slab up: concrete slab, sand-cement screed with Seal and Dry SBR, a coat of Weather Pro Hi-Flex, tile adhesive, then the tile with a filled grout joint between two tiles. Groutfills the joint, flushTilematt 300×300Adhesivefull bed, no hollow cornersHi-Flex coatwaterproofing, under the tileScreedwith Seal & Dry SBRSlabconcrete
Order as we use it on site: Seal & Dry SBR in the base coat, Hi-Flex under the tiles.
  1. Make the fall first. Cast the base coat with UltraTech Seal & Dry SBR in it, sloping to the drain from every side.
  2. Waterproof the floor. Apply UltraTech Weather Pro Hi-Flex. One coat covers 14–15 sq ft per kg (UltraTech); two coats need double.
  3. Fix the tile on a full bed of adhesive. For ceramic 300×300 indoors, Birla White TileStix Intero Grip+. For the 400×400 outdoor tile, the outdoor grade, TileStix Extero. We sell genuine Birla White with a GST bill.
  4. Fill every joint, flush. Birla White TileLynk grout is made for joints of 1–6 mm. An empty or low joint holds dirt and gives the foot nothing to catch.
  5. Keep feet off for a day. TX2 adhesive takes foot traffic after 24 hours (Birla White).

Worked example: a 5 × 7 ft bathroom floor

The floor is 35 sq ft. With 300×300 tiles at 7.75 sq ft a box, that is 4.5 boxes, so order 5 boxes and keep the extra for cuts at the drain. Hi-Flex at 14–15 sq ft per kg covers it with about 2.5 kg per coat. For your own floor use the tile calculator.

Seen on site

Four mistakes that make a floor slippery

Glossy tile on the shower side

It looks good on the shop table and fails the first time soap hits it. Glossy belongs on walls and on dry floors. See matt vs glossy.

Big tile where the floor must fall

A 600×600 tile on a bathroom fall either leaves a puddle or needs awkward cuts. Keep 300×300 on the wet side.

Buying from a photo

A photo cannot show a finish. Wet your palm and slide it across the face of the tile in the store. If your hand glides like on glass, so will a foot. This is our own quick check, not a lab test.

Joints left low or empty

Dirt and soap collect in a hollow joint, and the foot loses its edge. Fill flush, and wash the floor so scum does not build up.

Questions people ask us

Short answers

Which tile is not slippery for a bathroom floor?

A matt 300×300 floor tile, such as 393 matt or the Satvariyo-08 floor tile, with every joint filled and the floor falling to the drain. Keep glossy tile off the shower side.

What is COF in tiles?

COF is the coefficient of friction, the grip number. Higher means more grip, and the figure that matters for a bathroom is the wet one. H&R Johnson quotes 0.6 for a shower floor. Where makers disagree we use the higher figure.

What do R9 to R13 mean?

They are ramp classes: a tester in shoes walks on oil over a tilting ramp, and a steeper ramp before slipping earns a higher class. For bare wet feet there is a separate test with classes A, B and C. Villeroy & Boch advises R10 or R11 for an accessible bathroom.

Are smaller tiles less slippery?

They help. A 300×300 floor has 6.7 m of joint in every sq m against 3.3 m for 600×600, and joints give the foot an edge. The finish matters more: a small glossy tile is still glossy.

Can I use anti-skid tiles on a terrace?

Yes. The 400×400 Sasa Beige and Hexa Grey are Birla Pivot heavy-duty outdoor tiles with a rough face. Lay them on the outdoor grade of adhesive and give the terrace a fall to the drain.

Does the box show a slip rating?

Not that we can read. Birla Pivot's catalogue prints no slip number beside our bathroom floor tiles, and our two outdoor tiles carry only R1 in their names, which is Pivot's own label. We do not quote a number the maker has not given. If you need a tested figure, we will ask Birla Pivot for its test report.

Can I use the outdoor tile in a bathroom?

It grips, but at 400×400 it is large for a floor that must fall to a drain. Use it on open balconies and wash areas, and keep 300×300 matt for the shower.

Which tile for an elderly parent's bathroom?

Matt, small, and fully grouted, on the whole floor and not only the shower side, because wet feet drip onto the dry side. Keep the floor draining, and wash soap off it.

Mr Mustafaa
Tiles Engineer, Tashya Ventures

Looks after paint, putty and tiles at our Reva Road store, Muzaffarpur. Box sizes come from Birla Pivot's catalogue and the stock we hold. Slip figures come from the sources below, and where we have no number the page says so.

Where the numbers come from

  1. H&R Johnson India, bathroom tiles page (FAQ on non-slippery shower floors): textured or matt finish, COF 0.6.
  2. Houzz India, The best anti-slip floors for your bathroom: COF above 0.6 counted safe for bathrooms.
  3. Orient Bell, anti-skid tiles page: anti-skid R values 9 to 13, matt textured face, 300×300 and 600×600.
  4. Villeroy & Boch, slip resistance classes for bathroom floors: R10 or R11 for an accessible bathroom; classes A, B, C for barefoot areas.
  5. DGUV, FAQ on DIN EN 16165: the old oil-ramp (R) and barefoot (A, B, C) tests now sit in this one standard.
  6. Crossville, measuring for slip prevention: wet COF 0.60 for "slip resistant"; US tile standard minimum wet DCOF 0.42.
  7. Birla Pivot, tiles catalogue: heavy-duty outdoor tiles 400×400 (pp. 51 to 58), R2 to R4 shown on some designs only. Box contents and 11.8 mm thickness: Pivot's published figures as recorded for our stock.
  8. Birla White, TileStix and TileLynk product pages: adhesive grades, 1–6 mm joints, 24 hours before foot traffic. UltraTech, Weather Pro Hi-Flex sheet: 14–15 sq ft per kg per coat.

Tell us the room

Bathroom, terrace or parking, and the floor size. We will send the right tile, the boxes you need and today's price on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com