हिंदी Call90310 74624
Home›Tiles›Bathroom floor
Tile guide · bathroom floor

Bathroom floor tiles: which tile does not slip, and how to lay it right

The short answer
  1. Waterproof the slab
  2. Slope to the drain
  3. Matt 300×300 tile
  4. Joints filled full

On a wet floor, take a small tile with a matt or rough face, never a glossy one. Glossy glaze plus soap water is how people fall. In our stock, 393 floor matt is the one tile our bill marks as matt, so it is where we start.

300
mm tile, about 1 ftTwice the joint length of a 600 tile, and it follows the slope.
7.75
sq ft in one box8 tiles of 300×300 (Birla Pivot). Order by the box.
1st
Waterproof, then tileAfter tiling you cannot reach the leak. Do it before.
A bathroom floor, seen from above
Top view of a bathroom floor in 300 by 300 mm tilesA 5 by 6 foot bathroom floor in a grid of 300 mm tiles. The drain sits in the wet corner. Red arrows show the floor sloping from every side towards the drain. The wet corner is shaded and marked matt. The door is at the bottom left. 1 2 3 4 Top view: a 5 × 6 ft bathroom One square = one 300 × 300 mm tile
1 Drain: the lowest point. 2 Wet corner (shower), matt tile. 3 Red arrows: the floor falls towards the drain from every side. 4 Door side, the driest part. Plan for idea only; your drain may sit elsewhere.
Why people fall

A glossy floor is a skating rink with soap on it

A bathroom is the one room where we walk barefoot, wet, with soap on our feet. Three things decide whether the floor holds.

1The face of the tile

Soap and water spread into a thin film. On a smooth glazed face the film lies flat and the sole rides on it. A matt or rough face has tiny peaks that stand above the film, and the foot rests on them. Matt is not a guarantee: some matt glazes turn smooth with soap, so test the tile (see the test below).

2The joints

Every joint is a groove for the foot to catch on. Cut a square metre into 300 mm tiles and you get about 6.7 m of joint. Cut it into 600 mm tiles and you get about 3.3 m. That is plain geometry: joint length is 2 divided by the tile size in metres.

3Water that stays

A floor with no fall to the drain keeps a sheet of water on it, and standing water makes even a good tile slick. A small tile follows the slope; a big one sits flat and leaves pools along its edge.

Why a glossy tile is slippery when wetTwo close-up sections of a wet tile with a foot on it. On a glossy tile a film of soapy water lies over a smooth face and the sole floats on it. On a matt tile the tiny peaks of the face stand above the film and the sole rests on them. Glossy Matt / textured Smooth glaze, soapy water film on top: the sole floats. Tiny peaks stand above the film: the sole holds on them. water film covers the face peaks poke through Not to scale. Matt is not a promise: test it with soap (see below).
On our shelf

The tiles we have for a bathroom floor

We sell genuine Birla Pivot with a GST bill. One honest note first: our bills mark only one of the 300×300 floor tiles as matt. For the others, look at the face in the store and do the wet-foot test below before you order.

Birla Pivot 393 floor matt tile, blue wave pattern, 300 by 300 mm
Matt · start here

393 floor matt

300×300 ceramic. Our bill marks it "FloorMatt", the only floor tile in stock marked matt. A wave pattern that pairs with 393 LT on the wall.

Box: 8 tiles, 7.75 sq ft · Ask rate per box

Birla Pivot Satvariyo-08 floor tile, white marble print, 300 by 300 mm
Check the face

Satvariyo-08 floor

300×300 ceramic, white marble print. The maker's picture shows a shiny face and our bill does not state the finish. Touch it, wet it, test it before you choose it for the shower side.

Box: 8 tiles, 7.75 sq ft · Ask rate per box

Check the face

1145 floor

300×300 ceramic, the floor piece of the 1145 wall series. Finish is not marked on our bill; see it in the store.

Box: 8 tiles, 7.75 sq ft · Ask rate per box

Check the face

1217 floor

300×300 ceramic, the floor piece of the 1217 wall series. Finish is not marked on our bill; see it in the store.

Box: 8 tiles, 7.75 sq ft · Ask rate per box

Birla Pivot Sasa Beige outdoor tile 400 by 400 mm
Outdoor, rough face

Sasa Beige 400×400

Ultra Strong Outdoor vitrified, rough face. It works on a wet floor too, but it is 11.8 mm thick, so check the door step, and it needs vitrified-tile adhesive (below).

Box: 5 tiles, 8.61 sq ft · Ask rate per box

Birla Pivot Hexa Grey outdoor tile 400 by 400 mm
Outdoor, rough face

Hexa Grey 400×400

The grey twin of Sasa Beige: same size, same box, same laying notes. A good match for a balcony or wash area next to the bathroom.

Box: 5 tiles, 8.61 sq ft · Ask rate per box

Keep glossy for dry rooms. Our glossy 2×2 vitrified belongs in the hall and bedrooms. If you want one gloss tile in a bathroom, keep it on the dry strip by the door, well away from the shower. More on grip: anti-skid tiles · all sizes: 300×300 floor tiles. Today's price for every box: tile rates.

Before you pay

The wet-foot test, and what the slip numbers mean

A word like "anti-skid" on a box is a claim, not a test result. Test the tile yourself in the shop.

  1. 1
    Wet the tilePour a glass of water on one tile and spread it with your hand.
  2. 2
    Add soapA few drops of liquid soap. This is the real bathroom, not clean water.
  3. 3
    Step on it, barefootHold the shop shelf or the wall, put a wet bare foot down and push sideways, gently.
  4. 4
    Read the answerIf the foot glides, it is not for a bathroom. If it holds and you feel the texture, it is.

If the box prints a number

Two different tests are used. Do not mix them up.

TestClassSlip angle
Barefoot, soap waterDIN 51097, made for showersA · B · C12° · 18° · 24° (C grips most)
Shoes, oiled rampDIN 51130R9 to R13R10 from 10°, R11 from 19°, R12 from 27°, R13 over 35°

Another way to quote grip is COF (coefficient of friction). One published guide says 0.60 or higher is advisable for wet areas. Compare R with R, A/B/C with A/B/C and COF with COF; they do not convert.

Our stock: we have no maker's slip figure for these tiles and will not make one up. If the box shows a class, we read it out to you. The "R1" in the name of Sasa Beige and Hexa Grey is a Pivot name, not an R9–R13 class.

What to look for on the face
  • Matt, not satin. Rub a dry finger: it should drag, not slide.
  • Visible texture you can feel with a wet finger.
  • A small size (300×300), so there are many joints.
  • Dark or mid colour hides soap film and water marks better than pure white.
Size and slope

Why a small tile suits a floor that has to drain

The floor of a bathroom is not flat. It falls towards the drain, and the tile has to sit on that fall.

How much fall. Usual practice is about 1 in 50 to 1 in 100, which is 10 to 20 mm of drop for every metre of floor. The mason makes it in the screed, before waterproofing, and the drain sits at the lowest point.

A tile is flat. On a sloping bed it needs the bed beneath it to drop from one edge to the other: about 6 mm under a 300 mm tile, 12 mm under a 600 mm tile, at 1 in 50. A bigger tile means a thicker bed on the high side, a lip on the low side, or diagonal cuts around the drain. A 300×300 follows the fall with little fuss, and that is why bathrooms use it.

Wall and floor. They can match in colour, even the same series (393 or 1145). The floor tile must have the grippy face; the wall tile does not. Wall choices are on bathroom wall tiles.

Keep the whole floor one finish. Splash reaches every corner. A matt floor from door to shower is safer for children and elders than a mixed one.

Joint length in one square metre with 300 mm and 600 mm tilesTwo one-metre squares. The one cut into 300 mm tiles has about 6.7 metres of joint lines; the one cut into 600 mm tiles has about 3.3 metres. 300 × 300 mm 6.7 m of joint 600 × 600 mm 3.3 m of joint Joint lines in 1 square metre of floor Joint length = 2 ÷ tile size (in metres). Joints are where the foot grips.
The same square metre, cut two ways.
How much a floor drops under one tileA flat tile on a floor that slopes 1 in 50 sees the bed beneath it drop 6 mm under a 300 mm tile and 12 mm under a 600 mm tile. 300 mm 6 mm 600 mm 12 mm Drop of the bed under ONE tile at a 1 in 50 slope The red wedge must be filled by adhesive or a cut. Drawn about 2.5 times steeper than real so you can see it.
Slope is "1 in 50" = 20 mm drop per metre. Usual practice.
Under the tile

The tile does not make the floor waterproof

Tiles and grout let water through, slowly. The waterproofing sits under them, so it has to go in first. After tiling nobody can reach it.

Layers of the floor
Layers of a bathroom floor, bottom to topFrom the slab upwards: concrete slab, sloping screed with Seal and Dry SBR, two coats of Hi-Flex waterproof coating carried up the wall, tile adhesive, tile, and grout filling the joint fully. slope towards the drain 1 Tile, 300 × 300 matt or textured face 2 Grout, joint full no hollow, no gap 3 Tile adhesive TileStix, thin full bed 4 Hi-Flex, 2 coats up the wall too 5 Screed with SBR slope is made here 6 Concrete slab mason's work wall: coat goes up
Not to scale. Hi-Flex coverage is from UltraTech's sheet: 1 kg covers 14–15 sq ft for one coat.
  1. Screed with fall. Make the base coat with Seal & Dry SBR in it, sloped to the drain. Round the floor-to-wall corner.
  2. Hi-Flex, two coats. UltraTech Weather Pro Hi-Flex over the floor and up the wall. Let the coat dry as the pack says. Full method: bathroom waterproofing.
  3. Water test. Block the drain, hold a few cm of water for two days (standard practice) and look at the ceiling below.
  4. Adhesive. For 300×300 ceramic we stock Birla White TileStix Intero Grip+ (TX2): made for ceramic up to 450×450 mm, indoors, walk on it after 24 hours. For the 400×400 vitrified outdoor tile ask us for TileStix Vitribind (vitrified up to 600×600); we order it for you.
  5. Tile, from the drain side. Check the fall as you go. Keep joints even.
  6. Grout, joints full. Birla White TileLynk fills joints of 1–6 mm. Leave no hollow; an open joint is a path for water. Wipe the haze off the same day.

Never put putty or plain cement slurry under tiles as a "waterproof coat". We sell genuine Birla White and UltraTech with a GST bill; all of it can be ordered.

What goes wrong

Four mistakes we see in Muzaffarpur bathrooms

Glossy on the wet side

Glossy on the wet side

What you see: a fall, or a family that never uses that corner.

A glossy tile looks good in the shop and in the first week. Soap water makes it a slide. Fix: matt or textured on the whole floor, or at least the shower side.

drain puddle stays No slope

No slope

What you see: a puddle that stays for hours.

A dead-flat floor leaves water standing, and the grout turns black. Fix: the mason makes the fall in the screed; check it by pouring a bucket before tiling.

water goes to the slab Tiled first no waterproof coat under the tile

Tile first, waterproofing never

What you see: damp patch on the ceiling below, months later.

By then the only repair is breaking the floor. Fix: Seal & Dry SBR and Hi-Flex go in before the first tile, and a two-day water test.

Joints left open water goes down the joint

Joints left open

What you see: grout that cracks, tile that rings hollow.

Water goes down an open joint to the adhesive. Fix: fill the joint full with grout, wipe the haze, and keep the floor dry until it has set.

How many boxes

Boxes and waterproofing for your bathroom floor

Put in the floor size. The box figures are Birla Pivot's; Hi-Flex uses UltraTech's coverage. Walls need more coating: see the bathroom waterproofing page.

Floor area: — sq ft

Your list

Floor tile—Plain floor and 10% extra for cuts and breakage (usual practice for small tiles). Boxes only.—
Weather Pro Hi-Flex, floor, 2 coats—1 kg covers 14–15 sq ft per coat (UltraTech). Packs: 12 and 24 kg.—
Material totalAsk rate
Send this list on WhatsApp

Prices are filled in from today's rate. Whole house: tile calculator. Cutting and delivery are charged separately; ask for the amount for your site (delivery).

Questions people ask us

Short answers

Which tile is best for a bathroom floor?

A small tile, 300×300, with a matt or textured face, on a floor that has been waterproofed and sloped to the drain. In our stock that starts with 393 floor matt. See the tile list.

Which floor tile is not slippery when wet?

One with a matt or rough face and many joints. Do not trust the word "anti-skid" alone: wet the tile, add soap, and push a bare wet foot sideways in the shop. If it glides, leave it. Ratings, where printed, are explained above.

Glossy or matt tile for a bathroom floor?

Matt. A glossy glaze with soap water is a slide, and a fall on a bathroom floor is serious for elders. Keep glossy tiles for the walls and for dry rooms.

Which size tile is best for a bathroom floor?

300×300 (1 ft by 1 ft). It has about twice the joint length of a 600×600 and follows the fall to the drain with little cutting. Bigger tiles need a thicker bed or diagonal cuts around the drain.

Can I use the same tile on the wall and the floor?

They can match in colour, even the same series, but the floor tile needs the grippy face. A glossy wall tile on the floor is the mistake. Wall choices: bathroom wall tiles.

Are tiles waterproof? Is the bathroom floor waterproof once tiled?

No. Tiles are, but grout and joints let water through slowly. The waterproofing goes under the tiles: Seal & Dry SBR in the base coat and Hi-Flex over it. Read bathroom waterproofing.

How much slope should a bathroom floor have?

Usual practice is 1 in 50 to 1 in 100: 10 to 20 mm of fall for each metre towards the drain, made in the screed before waterproofing. Test it by pouring a bucket of water before you tile.

Can I use outdoor anti-skid tiles in a bathroom?

Yes, Sasa Beige and Hexa Grey (400×400) have a rough face and work on a wet floor. They are 11.8 mm thick, so check the door step, and as vitrified tiles they need vitrified-tile adhesive, not TX2. See anti-skid tiles.

Is 393 matt a good bathroom floor tile?

It is the one 300×300 floor tile whose bill entry says matt, so it is our first suggestion. Still do the wet-foot test with soap, as for any tile. Details: 393 floor matt.

How do I remove hard-water marks from bathroom tiles?

Wipe the floor dry after use, because marks come from water that dries on the face. Matt and textured faces hold marks more than glossy ones, so clean them often with a soft brush and mild cleaner. Strong acid damages grout and glaze: read why not acid on tiles.

How many boxes of tile do I need for a 5 × 7 ft bathroom?

The floor is 35 sq ft. One box of 300×300 is 7.75 sq ft, so 35 ÷ 7.75 = 4.5 boxes; with 10% extra for cuts, 38.5 ÷ 7.75 is nearly 5, so buy 5 boxes. The calculator above does it for your size.

What is the price of bathroom floor tiles per sq ft in Muzaffarpur?

Tiles are billed per box, not per sq ft. Divide the box price by 7.75 for the 300×300 floor tile. Today's price for each box is on tile rates, and every tile can be ordered.

What adhesive for 300×300 bathroom floor tiles?

For ceramic up to 450×450 indoors we stock Birla White TileStix TX2. Walk on it after 24 hours. The quantity guide is tile adhesive: how much.

Can I tile over my old bathroom tiles?

Only if the old tiles are sound and dry; that does not fix a leak. Read tiles on old tiles. Most bathroom leaks need the floor opened up.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint Engineer at our Reva Road store, Muzaffarpur, where tiles, adhesive and waterproofing sit on the same shelf. Box figures are from the Birla Pivot catalogue; coverage and adhesive limits are from the makers' sheets. Where we have no figure, the page says so.

Where the numbers come from

  1. Birla Pivot, product pages and tile catalogue: pieces and sq ft per box (300×300 floor: 8 tiles, 7.75 sq ft; 400×400 outdoor: 5 tiles, 8.61 sq ft, 11.8 mm thick). Finish for 393 floor: marked "matt" on our purchase bill.
  2. UltraTech, Weather Pro Hi-Flex product sheet: 1 kg covers 14–15 sq ft for one coat; two coats need double.
  3. Birla White, TileStix product sheets: TX2 Intero Grip+ for ceramic up to 450×450 mm indoors, walk after 24 h; Vitribind up to 600×600 vitrified; TileLynk joints 1–6 mm.
  4. DIN 51097 (barefoot wet areas, classes A, B, C) and DIN 51130 (oiled ramp, R9 to R13): the standards' published angles. Not tested by us.
  5. Other pages we read for what they say about slip: Kajaria, bathroom floor tiles (matt recommended, no figures); Homestyler, non-slip bathroom tiles (COF 0.60 or above advised for wet areas); Welspun Flooring blog (material types, no figures).
  6. Slope of 1 in 50 to 1 in 100, 10% extra tile, and the two-day water test are usual site practice, not a maker's figure.

Send us your bathroom size

We will send back the boxes, the waterproofing and the adhesive for your floor, with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com