हिंदी Call90310 74624
Home›Guides›Sanitary
Bathroom guide · western WC

220 mm or 300 mm toilet: measure your floor drain before you buy

The short answer

Hold a tape against the finished wall behind the toilet (the tile face, not the brick) and run it flat along the floor to the centre of the drain pipe. That number decides the WC for you. You don't get to choose it.

≈ 220
mm: CERA Chanel 220About 8¾ inch on a mistri's tape.
≈ 300
mm: CERA Cinco 300About 11¾ inch, nearly a foot.
Other
Send the number and a photoOn WhatsApp. We tell you what fits before you spend.
The number that decides the WC
Where the 220 mm and 300 mm are measured Side view of a one-piece western WC standing against a tiled wall. The tape starts at the tile face of the wall and ends at the centre of the drain pipe going down through the floor. 220 mm suits the CERA Chanel 220; 300 mm suits the CERA Cinco 300. hidden S-trap 220 mm → Chanel 220 300 mm → Cinco 300 1 Start at the tile face not the brick or plaster behind it 2 End at the pipe centre, not edge
Side view, roughly to one scale (bowl 660 mm long, 760 mm tall: CERA Chanel 220). The dashed grey line is where the drain sits for a Cinco 300. Trap distances from CERA's Chanel 220 and Cinco 300 pages.
Two minutes with a tape

How to measure the drain, step by step

An open pipe has no mark at its centre, and that is where most people go wrong. Take two readings and halve them.

Seen from above
Measuring the drain from above Top view of a bathroom floor. A tape runs from the tile face of the wall, square to the wall, across the open drain pipe. Reading A at the near edge of the pipe is 245 mm, reading B at the far edge is 355 mm. The centre is A plus B divided by two, 300 mm. tile face of the wall = 0 AB A = 245 B = 355 centre near edge far edge (245+355) ÷ 2 = 300 tape square to the wall ⌐
Drawn for a 110 mm pipe. The two-reading trick works for any pipe size, and with the old WC's rubber connector still in the hole.

1Find the pipe

A pipe mouth in the floor means an S-trap WC, and this page is for you. A pipe coming out of the wall means a P-trap WC, which is measured as a height instead: read S-trap or P-trap. If the old WC is still fitted, the pipe is hidden under it. Measure when the plumber lifts it, before you buy the new one.

2Find the finished wall

Start from the face of the tile on the wall behind the WC, at floor level. Wall not tiled yet? Measure anyway and tell the checker below; it takes off the tile and plaster still to come. If a skirting tile sticks out at the bottom, measure from the skirting and say so in your message.

3Take two readings

Keep the tape square to the wall and lay it across the pipe. Read A at the near edge and B at the far edge. The centre is (A + B) ÷ 2. If you only measure to the near edge, you will be about 55 mm short on a 110 mm pipe.

4Write it on the wall

Write the number on the wall in pencil and take a photo with the tape lying in place. Send that photo to us. It settles any doubt in a minute, and the plumber sees the same number on the day.

Check your number

Put in what your tape says

Millimetres or inches, both work. Tell us where you measured from, and the checker works out the distance from the finished wall.

Measured from
From the finished wall: —

What fits

—
Send this on WhatsApp, with the photo

Tile and plaster still to come are taken as usual practice: about 12 mm for wall tile on adhesive, about 25 mm for plaster plus tile. Today's price for each WC is on its page and on sanitary rates.

If it doesn't match

What happens with the wrong WC, or the wrong reading

The two sizes are 80 mm apart, about the width of your palm. That is too much for any connector to hide.

80 mm gap

A 220 WC on a 300 drain

You see: the tank stands a palm's width off the wall

The bowl has to come forward 80 mm to reach the pipe. The tank has nothing behind it, dirt and water collect in the gap, and the WC can rock. Don't accept it.

misses by 80

A 300 WC on a 220 drain

You see: it simply cannot be fitted

Against the wall, the outlet lands 80 mm past the pipe. To line up, the bowl would have to sit inside the wall. The only fixes are breaking the floor to move the drain, or changing the WC.

from brick: 325 ✗ from tile: 300 ✓ plaster + tile ≈ 25 mm

Measured from the brick

You see: the number reads about 25 mm too big

Plaster and wall tile together usually add about 25 mm. A drain that reads 325 from bare brick ends up at 300 from the tile: a Cinco, not "something in between".

edge: 245 ✗ centre: 300 ✓

Measured to the edge of the pipe

You see: a 300 drain reads 245

Half the pipe is lost, about 55 mm on a 110 mm pipe. That reading looks like "220-ish" and sends you home with the WC that cannot fit. Take both edges and halve.

Off by a little? Within about 15 mm either way, the plumber takes it up in the rubber pan connector, or with an offset pan connector (makers sell them with about 18–20 mm offset). We can order one for you. More than that means a different WC or moving the drain, and moving it is cheapest before the floor tiles go down.

Building or redoing the bathroom

Pick the WC first, then set the drain to it

Marking the pipe on a bare wall
Setting the drain pipe before plaster and tiles Side view of a bare brick wall and a slab, with the plaster and tile still to come drawn dashed, about 25 mm together. For a Cinco 300 the pipe centre is set 325 mm from the bare brick so that it ends up 300 mm from the finished tile. For a Chanel 220 it is 245 mm from the brick. 325 from bare brick = 300 from the tile plaster + tile to come≈ 25 mm (dashed) slab or floor bed cap it Chanel 220 → 245 from brick Cinco 300 → 325 from brick
Drawn for a Cinco 300. The 25 mm for plaster and wall tile is usual practice; if your mason plasters thicker, add the difference.

In a new bathroom the drain is not fixed yet, so you choose. Choose the WC model before the plumber sets the pipe, then place the pipe to suit it. Both our one-piece models take the same floor space (660 × 350 mm, CERA), so the choice is about the bowl, not the room.

Chanel 220 has a square bowl and siphonic jet flush and stands 760 mm tall. Cinco 300 has a swirl flush with a slim soft-close seat and stands 745 mm tall. Both are rimless, both have the S-trap hidden inside the body, both carry CERA's 10-year warranty for home use.

Upstairs bathroom? The pipe goes through the slab, and the hole or sleeve is fixed at the dhalai of that slab. Mark it on the shuttering with the figure from the brick (245 or 325 mm) before the concrete goes in. Put it on your chhat dhalai checklist.

Write the figure on the wall next to the pipe, and cap the pipe until the WC is fitted. When the plaster and tiles are done, measure again from the tile face. It should read 220 or 300 within a few millimetres.

Pan now, western later? In the room meant for a western WC later, lay this drain now and cap it, as our Orissa pan or western guide explains. Still deciding between one-piece, two-piece and wall-hung? Read wall-hung vs floor WC first. A wall-hung WC has no floor drain at all.

CERA at Rewa Road

The WCs, by drain distance

Catalogue numbers, sizes and trap distances are from CERA's own pages. CERA's pages for Celeb and the Conventional S-trap give no wall distance, so send us your number and we check it against the bowl in the store before you pay. Anything not on the shelf we order for you; ask on WhatsApp how long it takes. More: one-piece WCs · floor-mounted WCs · will it fit the room?

Questions people ask us

Short answers

What do 220 mm and 300 mm mean on a toilet?

They are the distance from the finished wall behind the WC to the centre of the drain pipe in the floor. Makers call it the trap distance or wall distance. CERA's Chanel 220 is made for 220 mm and its Cinco 300 for 300 mm.

Which is better, 220 or 300?

Neither. The drain in your floor decides it. In a finished bathroom you buy the WC that matches the drain. In a new one, pick the model you like and set the drain to it.

What is 220 mm and 300 mm in inches?

220 mm is about 8¾ inch and 300 mm is about 11¾ inch, just under a foot. If your mistri's tape reads 8½ to 9¼ inch, think Chanel 220; 11½ to 12¼ inch, think Cinco 300. The checker on this page takes inches too.

Can I fit a 300 mm WC on a 220 mm drain?

No. Against the wall its outlet lands 80 mm past the pipe, and the bowl cannot go into the wall. The floor would have to be broken to move the drain.

Can I fit a 220 mm WC on a 300 mm drain?

Only by pulling it 80 mm off the wall, which leaves the tank unsupported and a gap that collects dirt. Buy the Cinco 300 instead.

The old WC is still fitted. How do I measure?

The drain is under the old bowl, so you can't see its centre. Measure when the plumber lifts the old WC, before you buy the new one. Or send us a photo of the old WC with its name and the bill, and we try to read its trap distance from the maker's sheet.

My pipe comes out of the wall. Does this apply?

No. A wall outlet is a P-trap, measured as a height from the finished floor. India's standard for wash-down WCs (IS 2556 Part 2) puts the P-trap outlet centre at about 180 mm above the floor. See S-trap or P-trap.

Arun Tiwari
Thekedar · site work, costs and plumbing, Tashya Ventures

Arun Tiwari has fitted bathrooms on Muzaffarpur sites and sells the CERA range at our Reva Road store. Trap distances, sizes and catalogue numbers on this page were checked against CERA's own pages on 13 Nov 2026. Where CERA prints no figure (Celeb, Conventional S-trap), the page says so and we check the bowl for you.

Where the numbers come from

  1. CERA, Chanel 220 MM (S1013227): concealed S-trap, 220 mm wall distance, 660 × 350 × 760 mm, siphonic jet, 10 years residential warranty.
  2. CERA, Cinco 300 MM (S1013199): concealed S-trap, 300 mm wall distance, 660 × 350 × 745 mm, swirl flush, slim soft-close seat.
  3. CERA, Celeb (S1053121, 510 × 335 × 400 mm) and Conventional S Trap (S1053101, 520 × 360 × 390 mm, with Cajol seat cover): S-trap, no wall distance printed.
  4. Bureau of Indian Standards, IS 2556 (Part 2): 2004, washdown water closets, Table 2: P-trap outlet centre 180 mm (+15/−10) above floor; outlet outside diameter 102 ± 5 mm.
  5. studiomatrx, Floor-mounted toilet, India: S-trap measured from the finished wall to the drain centre; 220 and 300 mm common.
  6. Swan Street, How to measure toilet set-out: finished surfaces only, centre of the outlet not its edge, tile build-up of 10–12 mm.
  7. McAlpine and Multikwik offset pan connector listings (UK trade suppliers): offsets of about 18–20 mm.

Send us your number and a photo

Tape on the floor, wall to drain. We tell you which WC fits and send today's price on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com