हिंदी Call90310 74624
Home›Problems›Electrical
Electrical problem · MCB

MCB trips again and again: the six causes, in order, and what to do about each

The short answer

An MCB trips when the wire behind it is carrying more current than is safe, so a trip is a message, not a fault in the MCB. When it trips tells you why (the chart). To find the cause on one circuit:

  1. Switch off and unplug everything on that circuit.Phone chargers and the extension board too.
  2. Push the MCB up once.If it drops again at once, with nothing plugged in, stop: the fault is in the wiring.
  3. Switch things back on one at a time, a minute apart.The one that brings the trip back is your answer.
Never
a bigger MCB to stop itThe MCB protects the wire. Bigger than the wire, and the wire burns first.
÷ 230
Watts to ampsA 2,000 W geyser is about 9 A. Add up what runs together.
B / C
B for lights, C for motorsB trips at 3–5 × rating, C at 5–10 × (V-Guard Elegna sheet).
When does it trip? That is the cause
Find the cause of a tripping MCB from when it trips First: if it trips again the moment you reset it with everything unplugged, stop, it is a short in the wiring. Otherwise: after a few minutes of heavy load is cause 1, overload. The instant one appliance goes on is cause 2, that appliance. Only in rain or after a bath is cause 3, damp. At random with a warm board or a smell is cause 4, a loose or burnt terminal. Just as the AC, pump or fridge starts is cause 5, an MCB too small or a B-curve. On very little load with a loose handle is cause 6, an old or fake MCB. FIRST CHECK Drops again the moment you reset it, with everything unplugged? STOP Wiring short: leave it down, call an electrician. No? Then it trips… after a few minutes of heavy load 1 · Too much load on one circuit the instant one appliance goes on 2 · A fault in that appliance only in rain, or after a bath 3 · Damp or water in a point at random; board warm or smells 4 · Loose or burnt terminal just as the AC, pump or fridge starts 5 · MCB too small, or a B-curve ? on very little load; handle loose 6 · Old, worn or fake MCB RCCB (T button) fell instead? See “Which switch fell”.
Note what was running and when it tripped before you touch anything. Tell the electrician this and you save him an hour.
Look at the board first

Which switch fell? Each one means something different

Most houses we wire in Muzaffarpur have a main switch, sometimes an RCCB, and a row of MCBs, one per circuit. Only one of them has dropped. Find which.

A house distribution board with one MCB tripped From the left: the main switch, a double-pole MCB; an RCCB with a T test button, marked 30 mA; then four circuit MCBs marked B10 lights, B10 fans, C16 sockets with its handle down, tripped, and C20 AC. C40 DP T 30 mA B10 B10 C16 C20 lightsfanssocketsAC 1 2 3 1 Main switch2 RCCB3 One circuit MCB whole house offleak to earththe six causes below call electriciandamp, leakagehandle down, or in the middle = tripped
A typical board. Yours may have no RCCB, or a fuse unit in place of the main switch. Letters on each MCB: curve, then amps (C16 = C-curve, 16 A).

1The main switch fell

The whole house went dark. Either the total load is more than the main is sized for (two ACs, geyser and pump together), or a fault on one circuit was big enough to trip the main before its own MCB. Push the circuit MCBs all down, put the main up, then the MCBs up one by one. If the main falls on one of them, that circuit has the fault. If it falls with every MCB down, call an electrician.

2The RCCB fell (it has a T button)

An RCCB does not care about load. It trips when current leaks to earth: a damp switch box, a geyser element leaking into its body, a wire nicked by a nail. Same method: all MCBs down, RCCB up, MCBs up one at a time. The circuit that drops it has the leak. More in MCB vs RCCB.

3One circuit MCB fell

That circuit is drawing too much current, has a short, or the MCB itself is wrong or worn. This is what the six causes below are about. Read the letter and number on it first: you'll need them.

A small leak never trips an MCB. An MCB only feels big currents. In a house with no RCCB, a damp point can leave a switch plate or a tap live without tripping anything. If anyone feels a tingle, read current in the tap or body today.

The six causes, in the order to check them

From the most common to the least, and what fixes each

Go down the list in order. The first three you can check yourself with the circuit off. From four on, the fix is an electrician's job.

Iron1,000 W Room heater2,000 W Geyser2,000 W wire 18 A MCB 16 A ≈ 22 A 5,000 W ÷ 230
Cause 1 · most common

Too much load on one circuit

Signs: trips after some minutes, when heavy things run together

The heat strip inside the MCB warms slowly, so an overload can take a few minutes, sometimes much longer, to trip. It holds again once you switch one thing off.

Do this: add up the watts of what runs together on that circuit (checker below). Watts ÷ 230 = amps. Move the geyser, heater or iron to another circuit, or don't run them together. Don't raise the MCB above what the wire carries.

You can check this
1234 · TRIPS
Cause 2

A short or leak in one appliance

Signs: trips the instant one particular thing goes on, every time

A burnt geyser element, a cooler pump sitting in water, an iron cord worn at the handle, an old extension board: a fault inside the appliance pulls a big current at once and the MCB's magnet snaps it off.

Do this: everything unplugged, MCB up, then plug back one at a time with a minute's gap. The one that trips it stays out until it is repaired. If nothing you plug in trips it but it still falls, go on to cause 3.

You can check this
seelan in the box
Cause 3 · the monsoon one

Damp or water in a point

Signs: trips in rain, after the bathroom is washed, on the outside light or pump point

Water in a switch box or a junction lets current jump where it should not. If you have an RCCB, a little damp trips that first. The MCB falls when the water has made a proper short. Ground-floor walls with seelan and boxes on outside walls are where we find it.

Do this: keep that circuit off until the wall is dry. The rusted or blackened fitting gets replaced, and the water gets stopped, or it comes back next rain (seelan, foundation to roof).

Electrician to replace the point
C16 C16 loose: heats copper in,screw tight
Cause 4

A loose or burnt terminal

Signs: trips at random at normal load; MCB warm, smell of hot plastic, black marks

Years of heating and cooling loosen the screws. A loose joint gets hot, and the heat reaches the MCB's own heat strip, so it trips on a load it used to carry. It is worse in May and June: V-Guard rates the Elegna for up to 40 °C around it, and a metal board in the sun or beside the kitchen runs hotter than that.

Do this: main off, then the joint is remade: bare copper pushed fully in, no plastic under the screw, screw tightened (V-Guard gives 2 Nm for the Elegna). A burnt MCB or a blackened wire end is cut back or replaced.

Electrician, main switch off
B tripsC trips motor start 3×5×10×1×
Cause 5

An MCB too small, or a B-curve on a motor

Signs: trips just as the AC, pump, fridge or cooler starts, or when power returns after a cut

A motor pulls several times its running current for a moment as it starts. A B-curve MCB's magnet acts at 3 to 5 times its rating, so it can read that surge as a fault. A C-curve waits till 5 to 10 times and lets the motor start. When power comes back after a cut, every motor in the house starts at once.

Do this: check the wire first (checker). If the wire is right, the same rating in C-curve fixes it: Elegna C-curve. A 6 A on a socket circuit is simply too small: go up only as far as the wire allows. If a C-curve still trips, the motor is the problem (capacitor, jammed pump, low voltage): pump trips the MCB.

Electrician to change the MCB
C20 10000 AIS/IEC 60898-1 ISI ?
Cause 6 · check last

An old, worn or fake MCB

Signs: trips on very little load after 1–5 are ruled out; handle loose or won't stay up

V-Guard rates the Elegna for 4,000 operations under load. An MCB that has tripped a few thousand times, or been burnt by a loose joint, can start tripping early. A fake can do worse: not trip at all. A genuine one has its curve and rating, breaking capacity and IS/IEC 60898-1 printed on its face.

Do this: replace it with a genuine MCB on a bill, checking the box QR on V-Guard's site. How to tell: asli ya nakli MCB.

Electrician to fit
Check your load

Is this circuit simply asked to carry too much?

Put in what runs together on the circuit that trips, the wire it is wired in and the MCB on it. The checker says whether causes 1 and 5 are your problem.

Typical figures, shown so you can start. The plate on your appliance gives its real watts. Motors (marked ⚙) draw more amps than watts ÷ 230, so the checker adds a quarter for them.

This circuit

——
loadMCB ratingwire limit (V-Guard)
    Send this to Sashikesh on WhatsApp

    Wire limits are V-Guard's Classo+ figures (in a pipe / on the surface): 1 sq mm 11/12 A, 1.5 sq mm 13/16 A, 2.5 sq mm 18/22 A, 4 sq mm 24/29 A. The full chart: wire amps chart. Rating by circuit: which MCB for which load.

    What the letter on the MCB means

    B or C: why one MCB trips on a motor and the other doesn't

    Every MCB has two parts: a heat strip for slow overloads and a magnet for sudden big currents. The curve letter only sets the magnet.

    MCB trip curve, simplified Time to trip against current as a multiple of the MCB rating. Up to 1.13 times it never trips; from 1.45 times the heat strip trips it within an hour, faster as current rises. The magnet trips a B-curve instantly between 3 and 5 times rating, a C-curve between 5 and 10 times. A motor's starting surge, a few times rating for a fraction of a second, falls in the B band but short of the C band. 1 h1 min1 s0.1 s0.01 s Overload B C heat strip:slow, minutes 3–5 ×5–10 × Short:magnet,instant motor start a few × rating, a split second 1×1.45×3×5×10×20× Current, as times the MCB's rating → ■ up to 1.13 ×: does not trip for an hour — from 1.45 ×: trips within an hour, faster as it rises
    Simplified, log scales. B and C bands: V-Guard's Elegna spec sheet. The 1.13 × and 1.45 × points: the standard the Elegna is made to, IS/IEC 60898-1.
    CircuitCurve
    Lights and fansNothing that starts with a surgeB
    Plain sockets: TV, chargers, ironIf a cooler or mixer will plug in, treat it as a motor circuitB or C
    AC, fridge, coolerCompressor or motor startC
    Water pump, submersibleThe hardest start in the houseC
    Geyser, room heaterNo motor; sized by amps onlyB or C
    The curve never changes the amps. A C16 and a B16 both carry 16 A all day; C only lets a bigger start surge through. The amps are picked from the wire behind the MCB, never above it. Two cautions from V-Guard's own wire table: 2.5 sq mm in a pipe is rated 18 A, so a C20 belongs on 4 sq mm (24 A), or on 2.5 sq mm run on the surface (22 A). For 2.5 sq mm inside the wall, use a C16. Some charts print higher figures for 2.5 sq mm; we go by V-Guard's, because it is the wire we sell and the safer number.
    Bihar evenings make it worse. When the voltage sags in the evening, a motor takes longer to get up to speed and pulls its start current for longer, so a B-curve that held at noon trips at 8 pm. If voltage is your problem, read low voltage at home.
    When to stop

    Stop and call an electrician if you see any of these

    Leave the MCB down

    • It drops the moment you push it up, with everything on that circuit unplugged. The short is in the wiring.
    • A burning smell, black marks or melted plastic at the board, a switch or a socket.
    • A crackle or buzz from the board or a switch box.
    • Anyone felt a shock or tingle from a switch, tap, geyser or fridge body: current in the tap or body.
    • Water has reached the board or a box, after rain or a flood.
    • The MCB is hot to touch, or will not stay up at all.

    Never tape the handle up, hold it up, or wire across it. Push it up once on a trip; if it falls again at once, leave it.

    What to tell the electrician

    1. Which switch fell: main, RCCB or which MCB, and the letter and number on it.
    2. When it trips: the row of the chart at the top of this page.
    3. What was running, and whether it is worse in rain or in the evening.
    4. A photo of the board, open, with the power off.

    Send that photo to us on WhatsApp first and we'll tell you what we see. Need someone? We know electricians in Muzaffarpur who buy from us: electricians we know.

    On our shelf for this job

    The MCB and wire that fix it

    Every piece comes on a GST bill, with the box QR you can check on V-Guard's site. Today's price for each: electrical rates. Not sure which rating your board needs? Send us a photo of it.

    Questions people ask us

    Short answers

    Why does the MCB trip again and again? (MCB baar baar kyon girta hai)

    Six causes, in the order an electrician checks them: too much load on one circuit, a fault in one appliance, damp in a point, a loose or burnt terminal, an MCB too small or a B-curve on a motor, and an old or fake MCB. When it trips tells you which; the chart at the top of the page matches the two.

    What should I do when the MCB trips?

    Switch off and unplug everything on that circuit, push the MCB up once, then switch things back on one at a time, a minute apart. The one that brings the trip back is the cause. If it drops again the moment you push it up with everything unplugged, leave it down and call an electrician.

    Will a bigger MCB stop the tripping?

    It stops the tripping and takes away the protection. The MCB is there to protect the wire. V-Guard rates 2.5 sq mm wire at 18 A in a pipe, so a 25 or 32 A MCB on it lets the wire overheat inside the wall before anything trips. Move the load, or run a thicker wire for it. Check your wire on the wire amps chart.

    The MCB trips even when nothing is switched on. Why?

    If it trips the instant you push it up, there is a short in the wiring itself: a nail through a wire, a burnt junction, water in a box. Leave it down and call an electrician. If it trips some time later with nothing on, suspect damp (cause 3) or a loose terminal heating up (cause 4).

    It trips when power comes back after a cut. What is wrong?

    Every motor in the house (AC, fridge, cooler, pump) starts at the same moment, and each pulls several times its running current for a moment. Switch the AC and pump off during a cut and start them one at a time after it returns. If one circuit still trips on start, that circuit may need a C-curve MCB of the same rating.

    It trips only when it rains.

    Water is getting into a switch box, a junction or an outside fitting, usually on a ground-floor wall with seelan or an outside light or pump point. Keep that circuit off till the wall dries, have the fitting replaced, and stop the water at its source.

    What is the difference between the MCB and the RCCB tripping?

    An MCB trips on too much current: overload or a short. An RCCB, the one with a T test button, trips on current leaking to earth: damp, a geyser element leaking into its body, a wire nicked by a nail. A small leak never trips an MCB. More in MCB vs RCCB.

    Should I change my B-curve MCB to C-curve?

    Only if it trips as a motor starts (AC, pump, fridge, cooler), the wire is right for the rating, and the motor itself is healthy. Then a C-curve of the same amps is the usual fix. Never change the curve and raise the amps together. More in B-curve vs C-curve MCB.

    How long does an MCB last?

    Makers rate an MCB in operations, not years. V-Guard's spec sheet gives the Elegna 4,000 electrical operations and 10,000 mechanical ones, with a 5-year warranty. Replace it sooner if the handle is loose, it won't stay up, it is burnt or it trips on very little load.

    Sashikesh Kumar
    Diploma in Electrical, Tashya Ventures

    Looks after wiring, MCBs, fans, inverters and pumps at our Reva Road store, Muzaffarpur. The trip figures on this page were checked against V-Guard's own Elegna spec sheet and Classo+ wire table on 12 Nov 2026. Where charts disagree, the page says so and gives the safer number.

    Where the numbers come from

    1. V-Guard, Elegna MCB technical specification: B-type magnetic trip 3 In to 5 In, C-type 5 In to 10 In; 10 kA breaking capacity to IS/IEC 60898-1; ratings 6 to 63 A; ambient −5 °C to +40 °C; 4,000 electrical and 10,000 mechanical operations; terminal torque 2 Nm.
    2. V-Guard, Elegna MCB product page: B and C curve, 5-year warranty.
    3. V-Guard, Classo+ house wire page: current in conduit / clipped, 1 sq mm 11/12 A, 1.5 sq mm 13/16 A, 2.5 sq mm 18/22 A, 4 sq mm 24/29 A.
    4. V-Guard, Haize VX fan page: 1200 mm, 53 W (the fan figure in the checker).
    5. IS/IEC 60898-1, circuit-breakers for household use: no trip at 1.13 × rating for an hour, trip within an hour at 1.45 × (standard figures).
    6. V-Guard, product genuineness check, for the QR on the box.

    Tell us what trips and when

    Send a photo of your board and the row of the chart that matches. Sashikesh will tell you the likely cause, and the MCB or wire if you need one.

    TASHYABUILDING SOLUTIONS · MUZAFFARPUR
    WhatsApp 90310 74624tashyaventures.com