हिंदी Call90310 74624
Home›Calculators›Sariya
Free calculator · any size of house

Sariya calculator: how much steel your house needs, stage by stage

Thumb rules from JSW Neosteel, weights from IS 1786. Checked 12 Nov 2026.

The short answer
About 3.5 to 5 kg of sariya for every sq ft you build, on every floor.

A 1,000 sq ft ground floor takes about 35 to 50 quintal in all, and about half of it goes into the chhat. That is a thumb rule for budgeting and buying in rounds. Your engineer's drawing gives the exact list.

3.5–5
kg per sq ftOf built-up area, per floor. JSW Neosteel's figure.
~50%
Goes in the chhatSlab and its beams. Columns take about a quarter.
D²÷162
kg per metre12 mm: 12×12÷162 = 0.888 kg/m, 10.66 kg per 12 m bar.
Where the sariya goes in a house
Section through a one-storey RCC house showing the steel in each part Four stages: 1 neev, footings and plinth beam, 15 to 20 percent of the steel; 2 columns, 20 to 25 percent; 3 lintel and chhajja, 3 to 5 percent; 4 chhat, slab and beams, 45 to 55 percent. GROUND 1 1 2 3 4 STAGESHAREUSUAL SIZES 1 2 3 4 Neev + plinth beam Columns Lintel + chhajja Chhat + beams 15–20%20–25%3–5%45–55% 12, 16 mm · 8 mm rings 12, 16 mm · 8 mm rings 8, 10 mm · 6 mm rings 8, 10, 12 mm
Shares are the usual split published by house-building guides (HouseYog); stairs and the rest make up the balance. Sizes are usual for a small house. Your engineer's drawing decides both.
Calculator

How much sariya: whole house, or just the stage you are at

Any size works, even a single room or a 250 sq ft shop on the roof. Every number below says where it comes from.

Don't know the area? Use length × width

Built-up area means the covered area of the floor, walls included, not the plot. A plot of 2 katha is about 2,720 sq ft, but you may build on only part of it. See katha to sq ft.

Thumb rules, labelled

How the calculator works it out

Three rules, each from a named source. They are good for a budget and for ordering in rounds, not for cutting bars.

3.5–5 kg

Per sq ft of built-up area, per floor

JSW Neosteel's guide gives this range for a house, as a first estimate. We show the full range, and plan on the middle. For three floors or more, and for anything under 400 sq ft, we plan on the top figure: lower columns carry more, and a small house still needs full-size footings and columns.

Thumb rule · JSW
15 / 25 / 50%

Split by stage

Neev and plinth beam 15–20%, columns 20–25%, chhat with its beams 45–55%, lintel, stairs and the rest 5–10%. This is the usual split published by building guides. The sizes inside each stage are what is usual for a small house in north Bihar.

Usual practice
D × D ÷ 162

Kg per metre of bar

IS 1786 takes steel as 0.00785 kg per mm² of bar per metre, which works out to the diameter in mm, squared, divided by about 162. Pieces are counted as 12 m bars and rounded up, which covers small cutting waste.

Standard weight · IS 1786

The real list is your engineer's bar bending schedule (BBS). It names every bar, its size and its length. Send it to us on WhatsApp and we will weigh out exactly that. Before dhalai, send photos of the bars tied in place and we will look at them with you. More on what goes where: material for columns and beams.

Bar-weight checker

Check the bars delivered to your site

A bar that is too light is thinner than its size, and if you bought it per piece you got less steel. Weigh a bar, or a few together, and compare with the standard weight.

The sizes, drawn to scale
Cross-sections of 6, 8, 10, 12 and 16 mm bars to scale 6 mm weighs 0.222 kg per metre, 8 mm 0.395, 10 mm 0.617, 12 mm 0.888 and 16 mm 1.58. A 16 mm bar is seven times as heavy as a 6 mm bar. 68101216 mm 0.2220.3950.6170.8881.58 kg/m 2.664.747.4010.6618.96 kg/12 m
Twice the diameter is four times the weight. That is why a 16 mm bar weighs seven times a 6 mm bar.
SizeStandard kg per metrePer 12 m barBars per quintal
6 mm0.2222.66 kgabout 37
8 mm0.3954.74 kgabout 21
10 mm0.6177.40 kgabout 13.5
12 mm0.88810.66 kgabout 9.4
16 mm1.5818.96 kgabout 5.3
20 mm2.4729.6 kgwe order it for youabout 3.4
25 mm3.8546.2 kgwe order it for youabout 2.2

Standard weight per metre, from IS 1786. Full table and the soot names: sariya weight per metre.

Ask us about this weight

Weigh on a proper kaanta, measure the bar's length, and weigh several bars together if you can. One bar can be slightly off; a whole bundle should not be. To check the markings on the bar too: asli or nakli sariya.

Questions people ask us

Short answers

How much sariya for a 1,000 sq ft house? (1000 sq ft me kitna sariya)

By JSW Neosteel's thumb rule of 3.5 to 5 kg per sq ft, a 1,000 sq ft single-storey house takes about 3,500 to 5,000 kg, which is 35 to 50 quintal. Each extra floor of the same size adds about the same again. The engineer's bar bending schedule gives the exact figure.

Which size goes in the chhat? (chhat me kitne mm ka sariya)

JSW's guide names 10 and 12 mm for slabs, 8 mm for rings and stirrups, and 16 mm and above for columns, beams and footings. In small village houses 8 mm is often the lighter bar in the slab mesh. Your engineer's drawing decides, not the shop.

Why does your calculator take any area?

Because small houses are common here. Tata Steel's online estimator only accepts a ground floor between 578 and 1,934 sq ft, and Jindal's calculator still says "coming soon". For a very small build we plan on the top of the range, since footings and columns don't shrink with the floor.

How many bars in a quintal, and in a bundle?

A quintal is about 9.4 bars of 12 mm or 21 bars of 8 mm (see the table). A usual market bundle is about 50 kg: 10 bars of 8 mm, 7 of 10 mm, 5 of 12 mm or 3 of 16 mm, but makers differ, so we count and weigh at the counter.

How much lighter than standard can a bar be?

IS 1786 lets a single bar be at most 8% lighter for 6 to 10 mm, 6% for 12 and 16 mm, and 4% above 16 mm. A whole lot weighed together must be within ±7%, ±5% and ±3%. Use the checker above.

How much binding wire do I need?

Usual practice is about 1 kg of binding wire for every quintal of sariya, so 8 to 12 kg per tonne. The calculator adds it to your list.

Should I buy all the sariya at once?

Many families buy stage by stage, which is what the second mode is for. If you buy early, keep the bars off the ground on wooden blocks and covered, so they don't rust in fog and rain. Light surface rust that rubs off is normal; flaking rust is not.

Where the numbers come from

  1. JSW Neosteel, How much steel is required for a house?: 3.5–5 kg per sq ft of built-up area as a preliminary estimate; 8 mm for stirrups, 10/12 mm for slabs, 16 mm and above for columns, beams and footings.
  2. HouseYog, Steel required for house construction: share by element (foundation 15–20%, columns 20–25%, beams 20–25%, slabs 25–30%, stairs and other 5–10%).
  3. Bureau of Indian Standards, IS 1786:2008 (TMT bars): steel taken as 0.00785 kg per mm² per metre for nominal mass; mass tolerance by size for a batch and for a single bar.
  4. Tata Steel Aashiyana, Rebar estimator: accepts a ground floor of 578–1,934 sq ft only (seen 12 Nov 2026).
  5. Jindal Panther, TMT calculator: "Coming Soon" (seen 12 Nov 2026).
  6. Bundle counts and binding wire: usual practice in the market, labelled as such.

Send us your drawing, or just your stage

Tell us the floor area and the stage. We'll send back the sizes, pieces and today's price on WhatsApp, and cut to length if you want.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com