हिंदी Call90310 74624
Home›Steel›Cutting and delivery
Store service · sariya

Sariya cut to your lengths and delivered to your site in Muzaffarpur

The short answer
  1. 1Send your cut list on WhatsApp
  2. 2We cut at the store
  3. 3Our vehicle brings it to your site

For each bar, write three things: size, length, number of pieces. We cut Tata Tiscon or Saluja Gold bars to that list, tie them by size, load and deliver. The bill shows the weight of each size and the GST. Cutting and delivery are charged separately from the material price; ask for the amount for your site, and see delivery.

12 m
A full bar from the millAbout 39 ft. Longer than most lanes can turn with.
3
Things per lineSize in mm, length in m or ft, pieces. That is all we need.
kg + GST
On the billWeight of each size, so you can check it against your list.
Your list in, cut bundles out
From a WhatsApp cut list to cut bundles and a bill Step 1: a phone with a WhatsApp message listing 12 mm, 3.6 m, 40 pieces; 10 mm, 4.2 m, 30 pieces; 8 mm, 2.4 m, 100 pieces, and the site. Step 2: three bundles of bars cut to those lengths, drawn to scale. Step 3: the bill listing the weight of each size, cutting and delivery, and GST. T Tashya Ventures Cut list · Tata Tiscon 12 mm – 3.6 m – 40 10 mm – 4.2 m – 30 8 mm – 2.4 m – 100 Site: area + landmark Need it before: date ✓✓ ≈ 300 kg, 3 sizes Material + cutting + delivery: Ask rate 1 2 10 mm · 4.2 m · 30 12 mm · 3.6 m · 40 8 mm · 2.4 m · 100 04 m tied by size, lengths drawn to scale (a full bar is 12 m) 3 TAX INVOICE Tashya Ventures, Rewa Road · GSTIN on bill Tata Tiscon 12 mm128 kgAsk rate Tata Tiscon 10 mm78 kgAsk rate Tata Tiscon 8 mm95 kgAsk rate Cutting and deliveryAsk rate GSTAsk rate
Example list, not a recommendation for your house. Weights are the standard figures (12 mm 0.888 kg per metre, from JSW Neosteel's weight chart); your bill shows the weight of your bars.
Why cut at the store

A 12 m bar and a Muzaffarpur lane don't get along

Mills make sariya in 12 m lengths, about 39 ft. That suits a factory and a highway truck. It does not suit a gali with a turn, a gate between two houses, or a plot where the bars have to be carried in by hand.

Full bars versus cut bars at a lane turn, seen from above Top: a small vehicle carrying full 12 metre bars comes up a narrow lane. Before it reaches the turn, the front of the bars hits the wall of the house ahead, and the back would swing into the houses on the left as it turns. Bottom: the same vehicle, drawn to the same scale, carries bars cut to 4.2, 3.6 and 2.4 metres; they overhang only a little and the vehicle turns the corner. ✕ FULL 12 m BARS stuck before the first turn front end hits the wall ahead back swings into the houses 12 m ≈ 39 ft, nearly 3 times the vehicle ✓ CUT TO YOUR LIST short bundles turn the corner 4.2, 3.6 and 2.4 m pieces, same scale: a little overhang, not metres and two people can carry a bundle in through the gate
Seen from above, both pictures to one scale: a small vehicle about 4.3 m long and a narrow lane with a right-angle turn. Real lanes vary; the point does not.

1It reaches your site

Full bars overhang a small vehicle by metres at both ends. At the first turn the front hits a wall and the back swings into the houses. Cut pieces overhang a little or not at all, so the vehicle can come down lanes it otherwise could not.

2It goes in through the gate

A single 16 mm bar 12 m long weighs about 19 kg (JSW's chart: 18.94 kg), and it is longer than a three-storey house is tall. Getting it past a gate, round a corner and onto a small plot takes several people. A 3–4 m piece is easy to carry.

3No hacksaw work at the site

When full bars are cut on site, the mason cuts as the work goes, measures each piece by eye, and short ends pile up. When the pieces come cut to your list, your bar-bender starts tying on day one, and you can count what came against what you asked for.

Your engineer or thekedar works out the lengths; we cut what is on the list. How to read a bar list: bar bending schedule, lap and cover. Not sure how much steel you need in all? Sariya calculator.

Make your cut list

Type your list here, see the weight, send it on WhatsApp

One line per bar: size, length, pieces. The page adds up the standard weight of each size and shows how many full 12 m bars the pieces come out of. Then one tap sends the list to the store.

The three lines filled in are an example, not a list for your house. Change them, or clear them and type yours. Feet with inches: write 10 ft 6 in as 10.5.

Your list

Standard weight, all sizes—
Material, cutting and deliveryAsk rate on WhatsApp
Send this cut list on WhatsApp

Weight = standard weight per metre × length × pieces. Real bars can weigh a little more or less within BIS limits, and the bill shows the weight of your bars. "Full bars" is a simple plan with no allowance for the cut; we plan the cutting when we confirm. Today's price per kg: sariya rate.

SizeStandard weight per metreOne full 12 m bar
6 mm0.222 kg2.67 kg by formula
8 mm0.395 kg4.74 kg
10 mm0.617 kg7.40 kg
12 mm0.888 kg10.66 kg
16 mm1.578 kg18.94 kg
20 mm, 25 mm2.469 · 3.858 kg29.63 · 46.30 kg by formula, sizes we order for you

8–16 mm from JSW Neosteel's weight chart; 6, 20 and 25 mm from the same formula it gives, size × size ÷ 162 kg per metre. These are standard figures, not a weighed bundle.

Send it all at once

Send the whole stage together, not one line at a time

A 12 m bar does not divide evenly into every length. When we can see all the lengths of one size together, the end left over from one piece often becomes another piece on your list.

One 12 m bar, three ways to cut it
Cutting a 12 metre bar Row 1: only 4.2 metre pieces are needed, so each bar gives two pieces and a 3.6 metre end is left over. Row 2: the same list also has 3.6 metre pieces of the same size, so the end becomes a piece and nothing is left. Row 3: 3 metre pieces divide the bar into four with nothing left. A metre scale runs from 0 to 12 metres, about 39 feet. Only 4.2 m pieces on the list 4.2 m4.2 m 3.6 m left every bar leaves a 3.6 m end 4.2 m and 3.6 m on the same list 4.2 m4.2 m3.6 m the end is a piece you needed: nothing left 3 m pieces 3 m3 m3 m3 m divides exactly: nothing left 036912 m one full bar ≈ 39 ft
Only bars of the same size can share one bar. A 3.6 m end of 12 mm cannot become a 10 mm piece.
Cut lengthPieces per 12 m barLeft over
2.4 mabout 7 ft 10 in5nothing
3.0 mabout 9 ft 10 in4nothing
3.6 mabout 11 ft 10 in31.2 m
4.0 mabout 13 ft 1 in3nothing
4.2 mabout 13 ft 9 in23.6 m
10 ft3.05 m3about 9 ft 4 in
5.0 mabout 16 ft 5 in22.0 m
6.0 mabout 19 ft 8 in2nothing
"Nothing left" is on paper. The cut itself and the bar's own length tolerance take a few millimetres. If a length must be exact to the millimetre, write "exact" on that line and we will tell you before cutting. A run longer than 12 m cannot come from one bar; it needs two bars and a lap, which your engineer sets. See how long a lap should be.
After you send it

What happens between your message and your gate

We read it back

We reply with your list as we understood it, the weight of each size, and the amount: material at the day's rate, plus cutting and delivery for your site. Nothing is cut until you say yes.

We fix the day

We tell you when the vehicle can come. Send the list a day or two before you need the steel, and earlier before a dhalai, so the bars are on site before the masons are.

We cut, tie and load

The bars are cut to your lengths at our Rewa Road store, tied by size and length, and loaded. Rings are cut from 6 or 8 mm bar to the length of one ring, as your list says.

Delivered with the bill

Our vehicle brings it to your site in Muzaffarpur or nearby. The bill shows the weight of each size and the GST. Farther villages: see delivery.

When it arrives

Four checks before the vehicle leaves

Ten minutes at the gate saves an argument later. Do it with the bill and your list in hand.

Count the ends

Look at the cut end of each bundle and count the bars. The count for each length should match your list.

Read the bar

Brand and grade are rolled into the bar along its length. Check it says what you paid for: Tata Tiscon or Saluja Gold, and the grade on your bill.

Tape a few pieces

Measure two or three pieces from each bundle with a tape. They should be the length on that line of your list.

Match the bill

The bill gives the weight of each size. Check it against the standard weight of your list above, and keep the bill. Full checklist: when the sariya arrives.

Four checks when cut sariya arrives 1: the end view of a bundle with the bar ends being counted. 2: a bar with the brand and grade rolled into it. 3: a tape measure along a cut piece reading 3.6 metres. 4: the bill with the weight of each size next to the cut list, with ticks. 1 2 3 4 12345 count = list? BRAND · GRADE rolled into the bar same as the bill? 3.6 m length = list? bill your list kg of each size match?
Something short or wrong? Say so before the vehicle leaves and send a photo on WhatsApp the same day.
Brand cut-and-bend vs us

The steel makers' cutting services are built for big projects

Tata Steel and Jindal Panther both sell cut-and-bend steel. Their pages are written for builders and contractors, and neither names a centre in Bihar.

WhoWhat they offer, in their own words
Tata Steel ReadyBuildCut and bent at its service centres. Custom orders need a bar bending schedule or design drawing. Its FAQ says delivery usually takes 10–15 days. The contact page lists offices in Kolkata, Mumbai and Jamshedpur, and no centre in Bihar.
Jindal Panther cut and bendFactory cut and bend from your bar bending schedule. Its own page says small standalone homes may do fine with the traditional way. It gives no minimum order and no delivery time.
Tata Tiscon TechLabA free doorstep consultation, not a cutting service. When we checked on 1 Nov 2026, the booking form offered only Haryana, Rajasthan and West Bengal.
Tashya, Rewa RoadStraight cutting to your list, Tata Tiscon or Saluja Gold, for a single house. Send size, length and pieces on WhatsApp, or a photo of the schedule. We tell you the day when we confirm. Our own vehicle, and a bill with weight and GST.

Bent shapes beyond rings: send the schedule on WhatsApp and ask. This page covers cutting to length.

Lists that go wrong

Five ways a cut list causes trouble

"500 kg sariya bhej do" no size, no length, no count

Sending only the total kg

Result: we can send full bars, not cut ones

Nobody can cut from a total. Each line needs size, length and pieces.

drawing: span of the beam cut length: with bends, hooks, lap

Taking lengths off the drawing

Result: every piece comes up short

The cut length in a bar bending schedule already includes bends, hooks and laps. The span on the drawing does not. How a schedule works.

10 ? 10 m = 32 ft 10 in10 ft = 3.05 m more than three times apart

A length with no unit

Result: a phone call, or the wrong cut

Masons in Bihar often talk in feet; schedules are usually in metres or millimetres. Write m or ft on every line. If in doubt, we ask before cutting.

whole house, ordered on day one

Ordering the whole house at once

Result: bars sit in rain and mud for months

On a small plot with no dry storage, order by stage: foundation, columns, slab. Each stage's list is also easier to check. Storing sariya in rain and fog.

?

Not counting at the gate

Result: a shortfall found a week later

Count and tape before the vehicle leaves, with the bill in hand. A problem raised the same day is easy to put right.

Questions people ask us

Short answers

Can I get sariya cut to size in Muzaffarpur? (sariya katwa sakte hain?)

Yes. Send the size, length and number of pieces for each bar on WhatsApp to 90310 74624. We cut Tata Tiscon or Saluja Gold bars to that list at our Rewa Road store and deliver them to your site.

Is cutting free?

No. Cutting and delivery are charged separately from the material price. Ask on WhatsApp for the amount for your site; we tell you before anything is cut. See delivery.

How do I send my cut list?

One line per bar: size in mm, length (write m or ft), number of pieces. A clear photo of your bar bending schedule also works. Add the site location and the brand you want. The cut list box on this page writes the message for you.

My list is small. Will you still cut it?

Send it. We tell you the cutting and delivery amount for that list, and you decide. You can also collect from the store on Rewa Road.

Can you cut a piece longer than 12 m?

No single bar is longer than the standard 12 m, so a longer run is made from two bars overlapped (a lap). The lap length comes from your engineer's drawing or bar bending schedule. How long a lap should be.

What about rings (stirrups)?

Rings are bent from 6 or 8 mm bar. Put them on the list like any other line: the cut length of one ring and how many you need. Ready-made Tata Tiscon Superlinks we can order for you; ask on WhatsApp for the time it takes.

Will the bill show weight and GST?

Yes. The bill shows the weight of each size and the GST, so you can check it against your list and the day's rate.

Do you deliver outside Muzaffarpur city?

Yes, across Muzaffarpur and the nearby blocks in our own vehicle. For farther villages, send the village, block and nearest landmark and we quote the transport. See delivery.

Abhishek Ranjan
Diploma Civil Engineer, Tashya Ventures

Looks after cement and steel at our Reva Road store, Muzaffarpur. The weights on this page are the maker's published standard figures, checked on 12 Nov 2026. What the steel makers offer is taken from their own pages, as named below.

Where the numbers come from

  1. JSW Neosteel, TMT Bar Weight Chart: weight = size × size × length ÷ 162; 8 mm 0.395, 10 mm 0.617, 12 mm 0.888, 16 mm 1.578 kg per metre; 4.74, 7.40, 10.66, 18.94 kg per 12 m bar; standard length 12 m within BIS tolerances.
  2. Tata Steel ReadyBuild, home page and contact page with FAQ: cut and bend at service centres; custom orders need a BBS or drawing; delivery usually 10–15 days; offices in Kolkata, Mumbai, Jamshedpur.
  3. Jindal Panther, Cut and Bend Rebar: process from BBS to site; small standalone homes may manage with traditional methods; no minimum order or lead time stated.
  4. Tata Tiscon, TechLab booking page: free doorstep consultation; states offered Haryana, Rajasthan, West Bengal (seen 1 Nov 2026).
  5. Tashya Ventures store practice: cutting and delivery charged separately from the material price, for sariya and cement.

Send us your cut list

Size, length, pieces and your site. We reply with the weight and the amount, and the day we can deliver.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com