हिंदी Call90310 74624
Home›Steel›10 mm sariya
Steel · size

10 mm sariya: 7.40 kg a bar, 0.617 kg a metre, about 13.5 bars to a quintal

The short answer
Quantity10 mm sariya
1 metre0.617 kg
1 bar, 12 m7.40 kg
1 quintal (100 kg)13.5 bars
1 tonne135 bars

Standard weight from IS 1786, the same for every brand and grade. It is the "3 soot" bar of local speech. It is a slab and lintel bar: the engineer's drawing says where and how far apart. Price of one bar = rate per kg × 7.40.

Where 10 mm goes in your house
Where 10 mm bar goes in a house Three drawings, not to scale. Slab: 10 mm main bars along the short span near the bottom, with distribution bars laid across them. Lintel: two 10 mm bars at the bottom of the beam over a door or window, tied with stirrups. Stair: 10 mm bars along the sloping waist slab. Bar sizes and spacing always come from your engineer's drawing. 1 SLAB (chhat), side view wall / beam · span · wall / beam 10 mm main bar: bottom, along the short span dots = distribution bars across it 2 LINTEL over a door or window 2 bars of 10 mm at the bottom small ring (6 or 8 mm) round them top bars may be thinner 3 STAIR waist slab, side view 10 mm bars follow the slope plus bars across to spread load layout: engineer's drawing only Not to scale. Size and spacing: your engineer's drawing.
Slab and lintel bar sizes and spacing always come from the structural drawing. JSW's house guide names 10 and 12 mm as the usual slab sizes.
Where 10 mm is used

Slab, lintel, stair, small beam

For a village or town house, 10 mm is the bar most slab and lintel drawings use. Jindal Panther lists slabs, stairs and secondary beams as its main uses.

Slab (chhat)

The main bars run along the short span near the bottom; thinner or equal bars lie across them to spread the load. 10 mm is often the main bar; 8 mm often the cross bar.

Lintel over door and window

Usually two bars at the bottom, with small rings round them. The ring bar is thinner (6 or 8 mm); see 8 mm.

Stair waist and small beams

Bars follow the slope of the stair, with cross bars to spread the load. Small beams over a short span may also use 10 mm; longer spans go to 12 mm and up.

Where it is not enough

Columns and the main beams carry far more load and take thicker bars, as the drawing says. Do not swap a drawn size for a thinner one to save money.

Which bar suits your slab: slab bar size guide. How much steel the whole house takes: how much sariya and the sariya calculator.

Per kg, per piece, per quintal

The same steel, three ways of selling it

One bar, one quintal, one tonne
One bar, one quintal, one tonne of 10 mm A 12 m bar of 10 mm weighs 7.40 kg. About 13.5 bars make a quintal (100 kg) and about 135 bars make a tonne. One kilogram is 1.62 m of bar. 1 bar, 12 m7.40 kg 1 kg of bar is 1.62 m long 13.5 bars = 1 quintal (100 kg) 135 bars = 1 tonne (1,000 kg) (10 quintals; each little bar above = one 12 m bar)
Counted with 12 m bars. Cut bars: count by kg.

Dealers quote per kg, per quintal or per 12 m piece. They all convert with one number, 7.40 kg a bar. If a quote per piece looks cheap, divide it by 7.40 to get the real rate per kg.

Length cutWeight
1 m0.62 kg
3 m1.85 kg
4 m2.47 kg
6 m3.70 kg
9 m5.55 kg
12 m (full bar)7.40 kg

Cut bars are priced by weight, so the cut length changes the kg, not the rate. We sell by weight. Today's rate: sariya rate. Per kg, piece and quintal explained: how steel is sold.

Slab calculator

How many kg of 10 mm for a slab?

Only for planning. Put in the spacing your engineer drew. Laps, bends, chairs and cutting waste come on top, and the bar schedule in the drawing is the final word.

Bars in one metre
Bars in one metre width of slab Top view of a 1 m strip of slab with bars every 150 mm: 6.67 bars in a metre, 6.67 m of bar, 4.11 kg of 10 mm per square metre in one direction. 150 mm 1 m Top view: bars every 150 mm c/c 6.67 m of bar per sq m = 4.11 kg
Spacing c/cBar per sq m10 mm kg per sq m
100 mm10.00 m6.17 kg
125 mm8.00 m4.94 kg
150 mm6.67 m4.11 kg
175 mm5.71 m3.53 kg
200 mm5.00 m3.08 kg

One layer, one direction. A slab has bars both ways, and some may be 8 mm.

Your slab

Planning figure

Bar length—
Weight—
12 m bars—
Cost at your rateAsk rate
Send this to our counter

Add laps, bends and waste, or use the full sariya calculator.

Bundle

How many 10 mm bars in a bundle? Sources disagree.

Comaron prints a 12 m bundle of about 89 kg, which is about 12 bars. Steel On Call prints 45 to 50 bars, which would be 330 to 370 kg. Another guide says about 7 bars. These cannot all be right, and the maker's own pages give no count for 10 mm.

  1. Safe rule: go by weight, not by countBars are sold by kilogram. Read the weight on the maker's bundle tag and on your bill, and divide by 7.40 for the number of 12 m bars.
  2. ExampleA bill for 296 kg of 10 mm is 296 ÷ 7.40 = 40 bars of 12 m.
  3. Our counterAsk us for the bundle weight on your order and we will tell you the bar count from the tag on the bundle we send.
When it arrives

Weigh five bars, know in a minute

How much light IS 1786 allows
How much light is allowed on 10 mm Five bars together should weigh 37.0 kg. IS 1786 allows 7 percent either way, so 34.4 to 39.6 kg. One bar on its own may be at most 8 percent light, so not under 6.81 kg. A 10 mm bar weighing like an 8 mm bar (4.74 kg) is 36 percent light. -10%-7%0+7%+10% 5 bars together: 37.0 kg 34.4 kg39.6 kg green = allowed for the 5 together 1 bar alone: not below 6.81 kg (−8%) A "10 mm" that weighs 4.74 kg per 12 m is really an 8 mm: 36% light. Refuse it.
Tolerance on mass, IS 1786:2008 Table 2, for bars of 10 mm and under.
  1. Take five full barsDifferent places in the bundle, 12 m each. Weigh them together on a platform scale.
  2. Compare with 37.0 kg5 × 7.40. Between 34.4 and 39.6 kg is inside the 7 percent the standard allows.
  3. Far lighter means a thinner barAround 4.7 kg for a 12 m bar is an 8 mm bar sold as 10 mm. Do not use a ruler: the ribs make a bar read wider than it is.

The full weight chart and a checker: sariya weight per metre.

On our shelf

10 mm sariya, and what goes with it

Any size can be ordered; ask on WhatsApp for the time it takes. Today's rate per kg and per piece: sariya rate. Bars are cut to your list and delivered; cutting and delivery are charged separately, so ask for the amount for your site (delivery).

Questions people ask us

Short answers

What is the weight of 10 mm sariya per metre and per bar?

0.617 kg per metre, the IS 1786 standard figure. A full 12 m bar weighs 7.40 kg. It is the same for every brand and grade.

How many 10 mm bars make a quintal or a tonne?

With 12 m bars: about 13.5 bars to a quintal and about 135 to a tonne. If the bars are cut shorter, count by kilogram, not by pieces.

What is "3 soot" sariya?

"Soot" is local speech for one eighth of an inch, so 3 soot is 3/8 inch, about 9.5 mm. On the bill and from the maker it is the 10 mm bar. See the slab bar size guide.

Is 10 mm enough for a slab?

That is the engineer's call, not ours: it depends on the span, the load and the spacing. JSW's house guide names 10 and 12 mm as the slab sizes. Ask for the size and spacing in the drawing, and send us the list.

How many bars are in a bundle of 10 mm?

Online guides disagree by a factor of seven, so we do not print a count. Go by the weight on the maker's bundle tag and by the kilograms on your bill. See the bundle section.

Do Tata Tiscon and Saluja Gold 10 mm weigh the same?

The standard weight is the same, 0.617 kg per metre. Brands differ in grade and price, not in standard weight. See Tata Tiscon and Saluja Gold.

Will you weigh my 10 mm bars?

Yes. Ask at the counter and we weigh bars on our scale, including bars bought elsewhere. Cutting and delivery are charged separately from the material price; ask for the amount for your site.

Abhishek Ranjan
Diploma Civil Engineer, Tashya Ventures

Answers cement, steel and structure questions at our Reva Road store, Muzaffarpur. The 10 mm weight and tolerance on this page were checked against IS 1786:2008 on 12 Nov 2026. Where makers or guides disagree (bundle count), the page says so and gives the safe rule.

Where the numbers come from

  1. Bureau of Indian Standards, IS 1786:2008: Table 1 (10 mm: 0.617 kg per metre), Table 2 (tolerance on mass: 7 percent for a batch and 8 percent for one bar at 10 mm and under), clause 7.1 (cut length plus 75 mm, minus 25 mm).
  2. JSW Neosteel, How much steel is required for a house: names 10 and 12 mm as slab sizes and 8 mm for stirrups.
  3. Jindal Panther, TMT steel bar weight chart: 0.617 kg per metre, 7.40 kg for 12 m, about 135 pieces to a tonne, slabs, stairs and secondary beams.
  4. Comaron, 10 mm steel bar price guide (bundle of about 89 kg, with no per-bar rupee price) and Steel On Call, 10 mm rod weight and bars per bundle (45 to 50 bars): the two bundle figures that disagree.
  5. Kg per sq m of slab is our own arithmetic: 1,000 mm ÷ spacing × 0.617 kg per metre.

Send us your bar list

Sizes and number of pieces, or the kg from your engineer. We'll send back the weight and today's price, per kg and per piece, on WhatsApp.