हिंदी Call90310 74624
Home›Building in Bihar›Sariya
Building in Bihar · earthquake

Muzaffarpur is in earthquake Zone IV: what that means for your sariya and columns

The short answer

Muzaffarpur town and almost all of the district are in Zone IV, the second-highest of India's four zones, under IS 1893 (Part 1):2016. A house here needs no special or costly material. It needs five things done right:

  1. D-grade sariya: Fe 500D, Fe 550D or Tata Tiscon 550SD.
  2. Rings with 135° hooks, packed close near every beam-column joint and carried through it.
  3. Columns straight from footing to roof, with bars joined only in the middle half of each column.
  4. Bands in brick-wall houses: at plinth, lintel and roof level, running unbroken round the house.
  5. No open ground floor (shops or parking on bare columns, rooms above) unless an engineer has designed it.
Zone IV
High damage riskShaking up to MSK VIII. Zone V begins just north-east of the district.
75–100 mm
Rings near each joint3 to 4 inches apart, for at least 450 mm above and below.
135°
Ring hooksNot 90°. Hook ends at least 10 times the bar size.
Muzaffarpur and its neighbours
Earthquake zones around Muzaffarpur Schematic map. Muzaffarpur, Purbi Champaran, Sheohar, Saran, Vaishali and Samastipur are in Zone IV. Madhubani, most of Sitamarhi and north Darbhanga are in Zone V. The Zone V line runs just past Muzaffarpur's north-east corner. The 1934 earthquake, magnitude 8.3 on BMTPC's map, was centred near the Nepal border north of Madhubani. NEPAL 1934 · M 8.3 PurbiChamparan Sheohar Sitamarhi Madhubani Saran Darbhanga Vaishali Samastipur IVIVVV IVVIV IVIV Muzaffarpur ZONE IV Zone Vbegins onthis line Ganga Zone V very high damage risk (MSK IX+) Zone IV high damage risk (MSK VIII) Pin: our store, Rewa Road, Bhagwanpur
Schematic, not to scale: each box is a district. Zones as drawn on BMTPC's Bihar Earthquake Hazard Map (Vulnerability Atlas, 3rd edition), which follows the BIS seismic zone map. Epicentre from the same map.
Where the zone comes from

Why we say Zone IV, not V, and not the new "Zone VI"

Three different numbers float around for Muzaffarpur. Here is where each comes from, and the one to build to.

IVThe code in force

India's earthquake code, IS 1893 (Part 1):2016, puts Muzaffarpur in Zone IV. BMTPC, the government's building-technology council, calls it a high damage risk zone, with shaking up to MSK VIII. In the code's sums it carries a zone factor of 0.24, against 0.36 for Zone V.

VZone V is next door

Sitamarhi, Madhubani and north Darbhanga are Zone V, and the line runs just past the district's north-east corner. An older BMTPC district list even counts Muzaffarpur among Bihar's ten Zone V districts. If your plot is in the north-east blocks towards Sitamarhi and Darbhanga (Aurai, Katra, Gaighat), ask your engineer to check, and design for Zone V if in doubt.

VIThe map that was withdrawn

In late 2025 BIS issued a revised code with a new Zone VI. It withdrew that revision in March 2026, as reported at the time. So the 2016 map stands. If someone quotes "Zone VI" for north Bihar, that is the withdrawn map.

The local memory: the 1934 earthquake, centred near the Nepal border (magnitude 8.3 on BMTPC's map), badly damaged towns across north Bihar, Muzaffarpur among them. Masonry houses with nothing tying the walls together are what fell. The rules below are the cheap fixes for exactly that. Read them with the column and beam stage of our building guide.

Column and beam house

Where the rings go, and why the joint matters most

In a strong quake, a column fails near its top and bottom, where it meets the beams. That is where the rings must be close, closed with 135° hooks, and carried right through the joint. The middle of the column can have them wider.

Rings in a column between two floors A column between two beams. Rings are close, 75 to 100 mm apart, for at least 450 mm above and below each beam and through each beam joint. In the middle the rings are wider, up to half the column's narrow side. The vertical bars are joined by overlapping only in the middle half of the column. BEAMBEAM Through the joint rings carry on inside the beam, same spacing 75–100 mm apart 3–4 in, over at least 450 mm, h/6 or the wider side: the largest Middle of column not more than half the narrow side: 115 mm for a 9-in column, 150 mm for a 12-in column Close again above every floor, not only at the top And this joint too the most skipped spot Join bars only here middle half of the column close rings normal rings
A 12 × 12 inch column between floors 10 ft apart; heights squeezed to fit. Rules from IS 13920 as set out in IIT Kanpur–BMTPC Earthquake Tip 19.
WhereThe rule
Ring hooksTip 19, IS 13920135°, ends ≥ 10 × bar sizeAt least 75 mm. For an 8 mm ring, 80 mm. A 90° hook opens when the outer concrete cracks off.
Near every jointabove and below each beam75–100 mm apartSpacing up to ¼ of the narrow side, never over 100 mm. Over the largest of 450 mm, 1/6 of the clear height, or the wider side.
Inside the jointwhere beam bars crossRings continueMasons leave them out because the beam bars crowd in. Tie them in before the beam cage goes down.
Middle of the column≤ ½ narrow side115 mm (4½ in) for a 9-inch column, 150 mm (6 in) for a 12-inch one.
Joining column barslapMiddle half onlyRings over the lap at 100 mm spacing. Not all bars lapped at the same height.
Beam stirrupsIS 13920, Tip 18Close for 2 × beam depthFrom each column face: spacing ¼ of the beam depth there, half the depth in the middle. 135° hooks here too.
Column sizeTip 19300 mm (12 in) wideThe 1993 code let it drop to 200 mm only for columns under 4 m with beams under 5 m. See column size.
Columns run straight, footing to roof. No column standing on a beam, no column shifted on the upper floor, and the same column grid on every floor. If you build the ground floor now and the upper floor later, the footings and columns must be designed for both floors today, with bars left sticking out at the top: ground floor now, upper floor later.
What it costs. Doing the rings this way takes roughly 60 to 70 kg more 8 mm bar per floor for a 12-column house than rings at a flat 6 inches. Work out yours in the ring calculator below. The bar sizes and weights for the rest of the frame: sariya calculator.
Brick-wall house, no columns

The village house: bands hold the walls together

Most houses in our blocks are 9-inch brick walls under an RCC slab, with no columns. In a quake their walls split apart at the corners and fall outwards. A continuous concrete band ties them into one box. The lintel band is the one never to skip.

Bands and corner bars
Brick house with plinth band, lintel band and roof slab A one-storey brick house. A plinth band runs round the base. A lintel band runs over every door and window and turns the corner without a break. The RCC roof slab works as the roof band. Vertical bars stand in the wall at every corner and beside door and window openings. 1 2 3 4 1 2 3 4 RCC roof slabworks as the roof band Lintel bandover every opening, round corners Bars in the wallat corners and beside openings Plinth bandevens out soft-soil settling
Bands as described in IIT Kanpur–BMTPC Earthquake Tip 14 and IS 4326. The Bihar reconstruction guideline for brick-walled houses with an RCC roof shows the same.

Lintel band: the one that matters most

  • One band at door-top level, through every wall, over every door and window, and lapped round each corner. Not separate lintels over each opening.
  • IIT Kanpur's Tip 14 calls it the most important band and says it is needed in almost all buildings. It shows a lintel band 75 to 150 mm deep. In the 1993 Latur earthquake, one Killari house with a lintel band stood almost undamaged while most around it fell.

Roof and plinth bands

  • An RCC slab on the walls does the roof band's job, so no extra band is needed under it. A tin or asbestos roof needs a roof band.
  • A plinth band helps where the soil may settle unevenly, which on our soft river soil is most plots. It also carries the DPC.

Corners, openings and bars

  • Keep doors and windows small and away from corners. Walls lean on each other at the corners, and an opening there breaks that support (Tip 13).
  • A vertical bar in the wall at every corner, every T-junction and beside openings, tied into the bands. Your engineer gives the bar size by storeys.
The full village-house method, from plinth to slab bearing: the village house done right.
Which sariya

Why we push the "D" bar here, and where it stops helping

In a quake a bar that stretches and bends before it snaps buys time and keeps the frame standing. That stretch is what the "D" in a grade promises. The number in front is strength. For a house in Zone IV, the stretch matters more.

How far each grade must stretch before it breaks
Minimum elongation by sariya grade Minimum elongation under IS 1786: Fe 500, 12 percent. Fe 550D, 14.5 percent. Fe 500D, 16 percent. Tata Tiscon 550SD, 16 percent by Tata's own figure. A dashed line at 14.5 percent marks the D-grade level. 0%5%10%15% Fe 500plain 12% Fe 550D 14.5% Fe 500D 16% Tata 550SDTata's figure 16% D-grade line Minimum elongation, IS 1786. Longer = more warning.
IS 1786 minimums as tabulated by InfraLens and in Tata Steel's datasheet; Tata Tiscon 550SD figures from Tata's product page (yield at least 570 MPa, tensile at least 655 MPa).

What we stock, said plainly

  • Tata Tiscon 550SD in 6, 8, 10, 12 and 16 mm. Tata states at least 16% elongation, more than the 14.5% Fe 550D needs, and ties it to the IS 13920 seismic code.
  • Saluja Gold: the bars on our bills are marked Fe 500, a plain grade. Saluja also makes Fe 500D; we can order it for you, so ask on WhatsApp how long it takes.
  • Check the stamp on the bar itself: brand, grade with the "D", and the BIS licence number.

Where the grade stops helping

  • A D bar does not save a column whose rings are 8 inches apart with 90° hooks. Pay for the grade and the detailing; the detailing is the cheaper half.
  • More bars than the drawing asks for is not safer. It crowds the concrete so it cannot fill round the bars: what the grades mean.
Cutting and delivery are charged separately from the bar price. Ask for the amount for your site: delivery.
What goes wrong

Six site shortcuts that decide whether a house stands

Each picture shows the shortcut on the left (red is the mistake) and what a strong quake does to it on the right. All six are cheap to avoid while the cage is open, and impossible to fix after the dhalai.

135° OK 90° OPENS

Rings bent with 90° hooks

You see: column bursts, bars buckle out

When the outer concrete cracks off, a 90° hook simply unhooks and the ring springs open. A 135° hook is bent back into the core and holds. Tip 19 asks for 135° with ends at least 10 times the bar size.

NO RINGS

No rings inside the joint

You see: the joint cracks in an X

Where beam bars cross the column, masons leave the rings out because it is crowded. That joint then carries the biggest pull in the frame with nothing holding it. Put the joint rings on before the beam bars go in.

8–9 in

Rings widened to save steel

You see: a diagonal crack just under the beam

The commonest saving on Bihar sites, and the worst place to make it. Close rings near joints stop the shear crack and the bars buckling. For a 12-column house the difference is about 60 to 70 kg of 8 mm per floor.

ALL LAPSHERE

Bars joined at floor level

You see: the column snaps at the floor

Lapping every bar just above the slab is easy for the mason and puts the weakest point exactly where the column is worked hardest. Join bars in the middle half, with rings close over the lap, and stagger them.

OPEN GROUND FLOOR

Shops or parking on bare columns

You see: the ground floor folds, the rooms above drop

A ground floor with only columns and walled rooms above is soft and weak at the bottom. IIT Kanpur's Tip 21 notes such buildings collapsed in large numbers in the 2001 Bhuj quake. Build one only to an engineer's design.

NO LINTEL BAND

Brick house with lintels but no band

You see: corners split, cracks run from the windows

Separate lintels over each opening do not tie the walls. Without a band the walls part at the corners and fall outwards. One continuous lintel band through all walls is the cheapest earthquake insurance a village house can buy.

Rings for your house

How many rings, and how much 8 mm, done the Zone IV way

Put in your columns. The count follows the spacing rules above and is set against the common site habit of one ring every 6 inches with none in the joint. Your engineer's drawing is final; this tells you what to expect on the bill.

—

Your rings

Rings per column, per floor——
Length of one ring—Bent from 8 mm sariya, 40 mm cover, two 135° hooks of 80 mm. Standard weight 0.395 kg per metre.
8 mm for column rings, whole house———
Material totalAsk rate
Send this on WhatsApp

Column rings only; beam stirrups and the main bars are in the sariya calculator. Ring weight is rounded up to whole kg; add a little for cutting waste. Prices from today's rate.

Questions people ask us

Short answers

Is Muzaffarpur in seismic zone IV or zone V?

Zone IV under IS 1893 (Part 1):2016. BMTPC's Bihar earthquake hazard map shows the town and almost all of the district in Zone IV, with Zone V starting just past the north-east edge, in Sitamarhi, Madhubani and north Darbhanga. An older BMTPC district list counts Muzaffarpur among the Zone V districts because that line touches it. For a plot in the north-east blocks, ask the engineer to check, and design for Zone V if in doubt.

Does the new 2025 map with Zone VI apply?

No. BIS issued a 2025 revision of IS 1893 with a new Zone VI in late 2025 and withdrew it in March 2026. The 2016 map, with Muzaffarpur in Zone IV, is the one in force.

Is there an "earthquake-proof" sariya? (bhukamp rodhi sariya)

No bar makes a house earthquake-proof. A D grade (Fe 500D, Fe 550D, Tata Tiscon 550SD) stretches further before it breaks, which helps. Under IS 1786 that is 16% for Fe 500D and 14.5% for Fe 550D, against 12% for plain Fe 500. The rings, hooks and laps decide the rest.

Fe 500D or Fe 550D: which one for my house?

Both are ductile grades and both suit Zone IV. Fe 550D is stronger; Fe 500D must stretch a little more. For a house, what matters is that the bar is a D grade and that your engineer's drawing is based on it. Swapping grades means the engineer rechecks the bar count. More here: what the grade on a sariya means.

How far apart should the column rings be?

Near every beam-column joint, 75 to 100 mm (3 to 4 inches), over at least 450 mm, one-sixth of the column height, or the column's wider side, whichever is most. In the middle, no more than half the column's narrow side. Rings also continue through the joint. These are the IS 13920 rules set out in IIT Kanpur–BMTPC Earthquake Tip 19. Why rings matter: rings and stirrups.

Is a 9-inch column enough?

IS 13920 asks for columns at least 300 mm (about 12 inches) wide. Its 1993 edition allowed down to 200 mm only where the column is shorter than 4 m and the beams shorter than 5 m. A 9-inch column is the bare minimum for a small single-storey frame, not for a house that will grow to two or three floors. Your engineer decides.

My house is already built. Can it be made safer?

Often yes, but it needs an engineer to look at it first: adding bands or jacketing columns is design work, not a mason's job. Start with our list of engineers in Muzaffarpur.

Can you check my rings before dhalai?

Send photos of the column and beam cage on WhatsApp before dhalai and we will look at them with you: ring spacing near joints, 135° hooks, laps and cover blocks. It is not a structural design; that stays with your engineer.

Abhishek Ranjan
Diploma Civil Engineer, Tashya Ventures

Civil engineer at our Rewa Road store, Muzaffarpur, where he works out cement and sariya for houses every day. Every rule on this page was checked on 12 Nov 2026 against the BIS codes as explained by IIT Kanpur and BMTPC, and the zone against BMTPC's Bihar map. Where sources differ, the page says so and takes the safer side.

Where the rules and numbers come from

  1. BMTPC, Bihar Earthquake Hazard Map, Vulnerability Atlas 3rd edition (based on the IS 1893 seismic zone map): Muzaffarpur in Zone IV (MSK VIII), Zone V in Sitamarhi, Madhubani and north Darbhanga, 1934 epicentre marked M 8.3.
  2. BMTPC, Districts lying in earthquake hazard Zone V (Vulnerability Atlas 2nd edition): lists Muzaffarpur among 10 Bihar districts; zone factor 0.36.
  3. BIS, IS 1893 (Part 1):2016, Criteria for earthquake resistant design of structures: zone factors 0.24 (IV) and 0.36 (V).
  4. VisionIAS summary of The Economic Times, BIS revokes new seismic map with high-risk Zone VI, 7 Mar 2026.
  5. IIT Kanpur–BMTPC, Earthquake Tip 19: columns (IS 13920): 135° hooks with 10× extension, ≥ 75 mm; end zones and 75–100 mm spacing; D/2 in the middle; laps in the middle half; 300 mm minimum width.
  6. IIT Kanpur–BMTPC, Tip 18: beams, Tip 13: masonry layout, Tip 14: horizontal bands, Tip 21: open ground storeys.
  7. InfraLens, IS 1786 grades, and Tata Steel's Fe 550D datasheet: minimum elongation 12% (Fe 500), 16% (Fe 500D), 14.5% (Fe 550D).
  8. Tata Tiscon, 550SD product page: yield ≥ 570 MPa, tensile ≥ 655 MPa, elongation ≥ 16%, IS 13920.
  9. Also used: NIDM's Hindi guide to earthquake-safe housing, and the Bihar Disaster Rehabilitation and Reconstruction Project guidelines, Part 4 (brick-walled house with RCC roof).

Send us photos before the dhalai

Column and beam cage, close up. We'll look at the rings, hooks and laps with you and send the sariya list with today's price on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com