हिंदी Call90310 74624
Home›Building in Bihar›Eent
Building in Bihar · village house

The village house: 9-inch brick walls and an RCC lenter, done right

The short answer

Yes, it is a sound house. One or two storeys of 9-inch brick walls under an RCC lenter, with no columns, is allowed in Muzaffarpur's earthquake Zone IV. IS 4326, the code for this house, puts it in category D and asks for six things:

  1. Plinth above the worst water, with a plinth band on top that is also the DPC.
  2. 9-inch walls of awal bricks in 1:4 cement mortar, with the corners bonded, not butted.
  3. Small doors and windows: at least 450 mm from inside corners, and together no more than half of each wall.
  4. One lintel band through every load-bearing wall, its steel carried round the corners.
  5. A 10 mm bar standing in the wall at every corner, every T-junction and both sides of every opening.
  6. The lenter resting on the full wall width, never less than three-quarters, so it works as the roof band.

None of this needs costly material. A four-room house takes about 200 kg more of 6, 8 and 10 mm sariya and a dozen more bags of cement (calculator below). That is what keeps the walls from parting at the corners in a strong quake.

1:4
Cement : sand mortarIS 4326 for a Zone IV house. 1:6 is the figure for Zones II and III.
450 mm
Opening to inside cornerAbout 18 inches, at least. A door in the corner is the commonest mistake.
10 mm
Bar at every cornerAnd beside every door and window, one-storey house.
One outer wall, cut through
Cross-section of the outer wall of a one-storey brick house with RCC lenter From the ground up: brick footing on firm soil, plinth wall with filled floor inside, plinth band acting as DPC, 230 mm brick wall, lintel band, wall above, RCC slab across the full wall width, parapet. A 10 mm vertical bar runs from the plinth masonry into the slab. Plinth top is 2 ft above the worst water mark. worst water +2 ft OUTSIDE ROOM 230 mm · 9 in 1 Parapet 4½ in, on the slab 2 RCC lenter full wall width = roof band 3 Lintel band every wall, door-top level 4 9-in brick wall awal bricks, 1:4 mortar 5 10 mm vertical bar corners, junctions, jambs 6 Plinth band = DPC same section as lintel band 7 Plinth, rammed fill height from the water mark 8 Brick footing on firm soil
Not to scale. Rules: IS 4326:1993 for category D (Zone IV). Plinth height: how high in a flood area.
Why it stands or falls

Walls alone are four cards; tied together they are a box

A brick wall is strong along its length and weak across it. In a quake each wall needs the walls at right angles to hold it up. Three things make that happen, and every rule on this page serves one of them.

1Bands tie the walls

A continuous concrete band at lintel level, and one on the plinth, holds every wall to its neighbours like a belt round a box. The Zone IV page shows why the lintel band is the one never to skip.

2Bars stop the piers rocking

The strips of wall between doors and windows rock and crack in an X when the ground shakes. A vertical bar at each edge, anchored in the plinth and the lenter, makes them bend instead of break, and stops the wall sliding at sill or lintel level (IIT Kanpur–BMTPC Tip 15).

3The lenter is the lid

An RCC slab that sits on all the walls holds their tops together. That is why IS 4326 lets it replace the roof band, but only when it rests on the full wall, or at least three-quarters of it, and runs continuous over the inner walls.

Why category D: IS 4326 sorts houses by zone and importance. An ordinary house in Zone IV is category D, and for one or two storeys the code asks for the mortar, lintel band, vertical bars at corners, junctions and jambs, and a plinth band where the soil is soft. North Bihar's river silt is soft, so build the plinth band too.

Doors and windows

Where the openings go decides whether the corners hold

Every opening takes strength out of a wall, and an opening near a corner cuts the link between two walls. IS 4326 gives exact limits for a Zone IV house. Draw them on your naksha before the mason sets the first door frame.

Plan of a four-room village house
Plan of a four-room brick house with lintel band and vertical bars Four rooms with 9-inch outer walls and two cross walls. A dashed red line marks the lintel band over every wall. Red dots mark vertical bars at corners, junctions and both sides of each opening. A window sits at least 450 mm from the inside corner; two windows have a 560 mm pier between them. A wide front opening has a column at each side. ≥ 450 mm ≥ 560 mm Room Room Room Verandah room cross wall wide opening: a column each side openings ≤ ½ of the wall Lintel band, through every wall 10 mm vertical bar Column, only where the rules break
Example plan, not to scale. Limits: IS 4326:1993, Table 4, category D. The wide front opening breaks the limits, so it gets a column on each side, tied into the band.
Rule for a Zone IV houseLimit
Opening to inside corner of an outside wallIS 4326 Table 4: zero is allowed only in Zones II and below≥ 450 mm
All openings in one wall, added upShare of that wall's length, one-storey house≤ 50%
Same, two-storey houseEach floor's walls≤ 42%
Pier between two openingsThe strip of wall left standing≥ 560 mm
One opening above anotherVertical gap, two-storey house≥ 600 mm
Ventilator width≤ 900 mm
Two more rules from the same code. Keep the tops of all doors and windows at one level, so a single band runs over all of them. And no arches over openings: IS 4326 calls them a source of weakness. Where an opening has to break a limit, like a shop shutter or a wide verandah, it gets a concrete frame or bars round it, which in practice means a column on each side (see when a column is needed).

Check one wall

Measure one wall from inside corner to inside corner and put in its openings. It tests the three limits above.

Door about 3 to 3½ ft, window 3 to 4 ft. Measure the gap in the brickwork, not the frame. 450 mm is about 18 in; 560 mm about 22 in.

This wall

Openings, share of the wall—
Distance from corner—At least 18 in (450 mm), IS 4326 Table 4
Pier between openings—At least 22 in (560 mm). Not needed with only one opening.
Stage by stage

From neev to lenter, the order and the rule at each step

The plinth height and foundation type have their own pages; this is everything after the plinth level is fixed. Figures are IS 4326:1993 for category D unless marked.

  1. Fix the floor level and the footing

    Plinth height comes from the worst water on your plot plus 2 ft, and the footing from a test pit. Both are worked out on the flood-area plinth page. Set the corner and junction bars in the footing masonry now, before the plinth rises.

  2. Plinth walls and the plinth band

    Plinth walls in cement mortar, the inside filled in thin rammed layers. On top, a concrete band the full width of the wall, made like the lintel band. IS 4326 asks for it where masonry footings sit on soft or uneven soil, and says it serves as the damp-proof course too. Add WP+200 at 200 ml per bag of cement, UltraTech's dose.

    One band, two jobs: it ties the wall bases together and stops damp rising. More on damp: seelan from neev to chhat.
  3. Brickwork: awal bricks, 1:4, corners bonded

    Use well-burnt awal eent, wetted before laying so they don't suck the mortar dry. Mortar 1:4 cement : sand, joints about 10 mm and full. Build each corner first, stepped back, up to about 600 mm and fill the wall between; or leave toothed joints in both walls in lifts of about 450 mm. Never raise one wall and butt the next against it.

    1:4 (or 1:1:6 cement : lime : sand) is IS 4326's mix for category D. 1:6 is for categories B and C, which means Zones II and III.
  4. Vertical bars in pockets

    As the wall rises, the 10 mm bars at corners, junctions and door and window sides stay in a pocket in the brickwork, filled with 1:3 cement mortar (at least 10 mm round the bar) or M15 concrete as you go. Corner bars run from the plinth into the lenter; jamb bars from the floor up into the lintel band.

    Two storeys: 12 mm on the ground floor, 10 mm above (Table 7). Optional extra: 8 mm U-bars at sill level, 900 mm into each wall from the inside corner.
  5. Openings at one level, no arches

    Set all door and window tops at the same height so one band passes over all of them. Keep the limits in the table above. Where a wall must take a wide opening, the engineer frames it.

  6. Lintel band through every wall

    One continuous band over every load-bearing wall, inner cross walls included, at door-top level. Concrete M15 or 1:2:4, the full wall width, at least 75 mm deep. Two bars, one near each face, held by 6 mm links every 150 mm, with 20 mm cover. At corners and T-junctions the bars are bent round and lapped, never stopped short.

    Bar size goes by the longest wall between cross walls: table on the right. Separate lintels over each opening are not a band.
  7. Lenter on the full wall

    The slab sits across the whole 9-inch wall and runs unbroken over the inner walls; the corner bars end inside it. Done this way, IS 4326 needs no separate roof band. Thickness and slab steel: is a 4-inch lenter enough and sariya in the chhat; on the day: dhalai checklist; after: curing.

    IS 4326: the slab must cover the outer walls fully, or at least ¾ of their thickness. A slab sitting on half the wall, with a brick skin outside it, does not count.
The band, cut through and at a corner
Lintel band sections and corner bar detail Left: a 230 mm wall with a 75 mm deep band, two bars and a 6 mm link. Right: a 150 mm deep band with four bars in a closed link. Below: plan of a band at a corner, the outer bar bent round the corner and the inner bars lapped. 2 bars · walls up to 7 m full wall width 75 mm 75 mm, 2 bars, 6 mm links 4 bars · 7–8 m walls 150 mm 150 mm deep, 4 bars, closed links At the corner, from above Outer bar bent round the corner. Inner bars lapped past each other. Lap length as on the drawing. Bars never stop at the corner.
Bands: IS 4326 clause 8.4.5 and Table 6; corner detail after its Fig. 11. Most bands in a small house are the left one.
Longest wall between cross wallsBand bars
Up to 5 m (16 ft)2 × 8 mm
6 m (20 ft)2 × 10 mm
7 m (23 ft)2 × 12 mm
8 m (26 ft)4 × 10 mm
HouseVertical bar at each corner, junction and jamb
One storey10 mm
Two storeys, ground floor12 mm
Two storeys, upper floor10 mm

IS 4326:1993 Tables 6 and 7, category D, for HSD (TMT) bars. Over 8 m, add a cross wall or pilaster. Your engineer's drawing is final.

Where the walls stop being enough

When a column is still needed, and when to build a frame instead

A brick-wall house works when walls are short, cross walls come often and openings are small. These six situations break that, and each has a fix. Whether to go for an RCC frame for the whole house is weighed on the 1000 sq ft cost page.

A wall longer than 8 m

No cross wall for 26 ft or more

IS 4326's band table stops at 8 m. Beyond that it asks for a pilaster or buttress to cut the span, or a special design.

Fix: put in a cross wall, or a column tied into the band and the slab.

A wide opening

Shop shutter, verandah, car or tractor bay

An opening wider than the wall limits allow takes out the wall that was carrying the roof there. The code asks for it to be framed in concrete.

Fix: a column each side and a beam over it, tied into the lintel band, to the engineer's drawing.

A floor coming later

Upar baad mein

IS 4326 allows bearing walls up to four storeys, but only when walls, bars and footing are designed for them: two storeys need 12 mm bars below and openings within 42%. Some cement makers' guides ask for 12-inch walls for two storeys (JK Cement).

Decide before the first lenter: ground floor now, upper floor later.

Soft, filled or flood land

Chaur, pond fill, river bank

Walls on soft ground settle unevenly and crack whatever the bands. The NIDM guide for Bihar gives brick or RC piles with a beam on top for such plots.

Fix: test pit first, then the foundation from the plinth page, chosen by an engineer.

An L, T or U-shaped house

Rooms added at an angle

Wings of different size shake differently and tear at the joint. IIT Kanpur's Tip 13 suggests splitting the plan into near-rectangular blocks unless the projection is small, about 15 to 20% of the length.

Fix: keep each block a simple rectangle, or ask the engineer for a gap between blocks.

A big room or a beam on a wall

Hall wider than the slab can span

A long room needs a beam under the lenter, and a beam end puts a heavy point load on a small patch of brick.

Fix: a column or concrete bed block under each beam end. Slab spans: 4-inch lenter.

Shops or parking on bare columns with walled rooms above is a different building altogether. Don't build it without an engineer's design: why the open ground floor fails.

What goes wrong

Six site habits that undo a brick-wall house

Each picture shows the habit on the left (red is the mistake) and what a strong quake or a few monsoons do to it on the right. All six are free to avoid while the wall is going up.

AT THE CORNER

Door or window at the corner

You see: cracks from the opening, corner pulls apart

The corner is where two walls hold each other up. An opening there cuts that link (IIT Kanpur–BMTPC Tip 13). Keep 450 mm of solid wall from the inside corner.

1:6 · 1:8

Lean mortar and hollow joints

You see: X cracks, sand falling from the joints

Mixing 1:6 or 1:8 to lay faster, or leaving joints half filled. Zone IV asks for 1:4 and full 10 mm joints. Bricks must be stronger than the mortar, and wetted first.

HALF THE WALL

Lenter on half the wall

You see: crack along the wall top, slab shifts

A half-brick skin built outside the slab to hide its edge leaves the lenter on 4½ inches. IS 4326 wants the full wall, at least ¾ of it, or a separate roof band.

NO BARS

No vertical bars at corners and jambs

You see: X cracks in the strips between openings

Without bars the piers rock and the wall slides at sill or lintel level (Tip 15). A 10 mm bar at each corner, junction and jamb costs a few kg per point.

STRAIGHT JOINT

Walls raised one at a time

You see: a clean vertical crack at the corner

One wall finished, the next butted against it with a straight joint: the two never become one. Build corners first, stepped, or tooth both walls in 450 mm lifts.

ARCH

Arches and wide openings in bearing walls

You see: cracks over the arch, walls pushed out

An arch pushes sideways on the wall that holds it. IS 4326 says to avoid arches over openings, or to tie them with steel. Wide openings need a frame.

Steel for your bands

Band and corner-bar steel for your house

Put in your walls. The tool picks the band bar from IS 4326's table for your longest wall and counts the vertical bars, links and band concrete. It covers only the earthquake steel; slab steel is on the chhat sariya page.

Run = length of all walls of that kind added up. 4½-inch partitions carry no slab; leave them out. Count a crossing of two walls as one junction.

Your earthquake steel

Band bars—
8 mm sariya—Bands with 10% for laps and corners, plus vertical bars with 0.6 m of anchorage. Standard weight per metre.
10 mm sariya—Bands with 10% for laps and corners, plus vertical bars with 0.6 m of anchorage. Standard weight per metre.
12 mm sariya—Bands with 10% for laps and corners, plus vertical bars with 0.6 m of anchorage. Standard weight per metre.
6 mm sariya, links—
Material totalAsk rate
Send this list on WhatsApp

Planning figures from IS 4326 and our arithmetic, not a bar bending schedule; your engineer's drawing is final. Cutting and delivery are charged separately; ask for the amount for your site (delivery). Prices are filled in from today's rate.

Questions people ask us

Short answers

Can I build a house without columns in Bihar? (bina column ka ghar)

Yes, for one or two storeys, if it follows IS 4326 for Zone IV: 1:4 mortar, openings at least 450 mm from corners and within half the wall, a lintel band through every wall, 10 mm vertical bars at corners and jambs, and a lenter on the full wall. Long walls, wide openings and soft ground still need columns or a frame.

How thick should the wall be for a load-bearing house?

9 inches (230 mm) for every wall that carries the lenter. IS 4326 assumes at least 200 mm for walls with bands. 4½-inch walls are only for partitions that carry nothing. For two storeys the engineer may ask for thicker ground-floor walls.

Is a lintel band needed in Zone IV?

Yes. IS 4326 asks for it in every category D house, on all load-bearing walls, inner ones too, and IIT Kanpur calls it the most important band. Separate lintels over each door are not a band. See Zone IV.

Do I need a roof band under the lenter?

Not if the RCC lenter rests on the full wall, or at least three-quarters of it, and runs continuous over the inner walls. Then the slab does the band's job (IS 4326 clause 8.4.3). A tin or asbestos roof does need a roof band.

Is 1:6 mortar enough for a village house?

Not in Zone IV. IS 4326 gives 1:6 for categories B and C (Zones II and III) and 1:4 cement : sand, or 1:1:6 cement : lime : sand, for category D, which is an ordinary house in Muzaffarpur.

Some sites say openings should be one-third of the wall. Which is right?

Both are IS 4326 figures for different houses. One-third (0.33) is the category D limit for three or four storeys. For one storey it is half, for two storeys 0.42. The 450 mm corner gap and 560 mm piers apply to all of them.

Can I add a first floor later on a load-bearing house?

Only if the footing, walls and bars were sized for two floors: 12 mm vertical bars on the ground floor, openings within 42% of each wall. A house built for one floor is not. Decide before the first lenter: ground floor now, upper later.

How many bricks and how much cement does a village house need?

Count from your walls: about 9.7 bricks per sq ft of 9-inch wall, in the brick counter. For a whole 1000 sq ft house with walls carrying the lenter, the 1000 sq ft list gives 350–420 bags of cement and 1.5–2.2 t of sariya. The full village list: village brick house cost.

What is DPC and is it needed in a village house?

A damp-proof course: a waterproofed concrete layer across the full wall at plinth top, so ground water can't climb into the wall. Yes, it is needed. In this house the plinth band does the job, with WP+200 in its concrete.

Can you check my walls before the lenter?

Send photos on WhatsApp before plaster and before dhalai: corners, door and window positions, the band steel and the corner bars. We will look at them with you. It is not a structural design; that stays with your engineer.

Abhishek Ranjan
Diploma Civil Engineer, Tashya Ventures

Civil engineer at our Rewa Road store, Muzaffarpur, where he works out cement, sariya and bricks for village houses every day. Every rule on this page was checked on 13 Nov 2026 against the text of IS 4326:1993 and the IIT Kanpur–BMTPC Earthquake Tips. Where sources differ, the page says so and takes the safer side.

Where the rules and numbers come from

  1. BIS, IS 4326:1993, Earthquake resistant design and construction of buildings: Table 2 (Zone IV, importance 1.0 = category D), Table 3 (mortar 1:4 or 1:1:6 for D), clause 8.2.4 (corners first to 600 mm or toothed joints in 450 mm lifts), Table 4 (openings), clauses 8.3.2–8.3.6 (openings at one level, framing, no arches), Table 5 (strengthening a to g), clauses 8.4.2–8.4.7 (lintel, roof and plinth bands; slab on ≥ ¾ of the wall; plinth band as DPC; sill dowels), Table 6 (band bars by span), Table 7 (vertical bars), clause 8.1.2.2 (bar cover in 1:3 mortar or M15).
  2. IIT Kanpur–BMTPC Earthquake Tips: Tip 12 (brick houses, 10 mm joints, wet bricks), Tip 13 (openings near corners, plan shapes, 15–20% projections), Tip 14 (bands; RCC slab replaces roof band; 75 mm, 2 × 8 mm, 6 mm links at 150 mm), Tip 15 (vertical bars, pier rocking and sliding).
  3. NIDM (GoI–UNDP), guide to flood-resistant houses in Bihar's alluvial areas: foundations for soft soil, as set out on our plinth page. Zone IV for Muzaffarpur: IS 1893 (Part 1):2016, as on our Zone IV page.
  4. UltraTech Weather Pro brochure: WP+200 at 200 ml per 50 kg bag. JK Cement, load-bearing vs framed structures (12-inch walls for two storeys). Brick count per sq ft: our eent page.
  5. Bihar's reconstruction guideline for brick-walled houses with an RCC roof (Part 4) is often cited for this house; we could not open a copy online on 13 Nov 2026, so every figure here is taken from IS 4326 directly.
  6. Calculator: standard weight per metre (6 mm 0.222, 8 mm 0.395, 10 mm 0.617, 12 mm 0.889 kg); M15 as 1:2:4 with 1.54 dry-volume factor (standard figure); 10% for laps, 0.6 m anchorage for corner bars, jamb bars 2.1 m plus 0.45 m, link lengths 0.30 m (two bars) and 0.75 m (four bars): our arithmetic.

Send us your naksha

We'll mark the corners and openings against the Zone IV rules and send back the cement, sariya and brick list with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com