हिंदी Call90310 74624
Home›Guides›Steel
Steel guide · roof slab

How much sariya for a roof slab: the 1000 sq ft chhat worked out

The short answer

A 1000 sq ft chhat drawn with 10 mm bars at 6 inches takes about 1.3 tonnes of sariya. With 12 mm main bars, about 1.4 tonnes. That counts the top bars over the beams and 10% for laps and cut ends.

  1. Number of bars
  2. Length (m)
  3. kg per metre
  4. Top bars
  5. 10%

The 4 kg per sq ft figure you see online is for a whole house, footings to roof. Use it for a roof and you buy about three times too much. Your drawing sets the bar size and spacing. This page shows how to turn them into kg and into pieces the shop sells.

1.3–1.4 t
1000 sq ft roof slabOur worked example, top layer included.
≈ 180
Bars of 12 mFor the all-10 mm version. Billed by weight.
11–17 kg
Binding wireUsual practice: 8 to 12 kg per tonne of sariya.
One room of slab, seen from above
Slab steel in one room, plan view A 12 ft by 10 ft room with beams on all four sides. Red main bars run across the short 10 ft side at 6 inch spacing. Dark distribution bars run the long way, tied on top. A yellow band along every beam marks the top bars, the second layer over the supports, reaching about a quarter of the span into the room. 6 in 150 mm c/c 12 ft 10 ft Main bars bottom layer, across the short side Distribution bars the long way, tied over the main bars Top bars over beams and walls second layer, about ¼ of the span into the room Beam or wall under the slab
Bars drawn fewer than real so they stay readable. In a room this near square (12 × 10 ft), the slab works both ways, so your drawing may show working bars in both directions.
The number most pages get wrong

4 kg per sq ft is the whole house, not the chhat

Search "1000 sq ft slab steel" and most pages say 3,500 to 4,000 kg. That is a house figure: footings, columns, beams and slab together, per sq ft of built-up area. The roof slab is about a third of it.

Steel for 1000 sq ft: slab against whole house Slab bottom mesh alone: 0.59 to 1.12 tonnes. Complete slab with top bars and 10 percent allowance: 1.31 to 1.40 tonnes. Whole house, footings to roof: 3.5 to 5 tonnes. The 4 kg per sq ft rule lands inside the whole-house bar. 01 t2 t3 t4 t5 t Slab, bottom mesh only 0.6–1.1 t Slab with top bars + 10% 1.3–1.4 t what the roof needs Whole house, footings to roof 3.5–5 t "4 kg/sq ft" Tonnes of sariya for 1000 sq ft
Slab bars: our 40 × 25 ft worked example below. House range: JSW Neosteel's guide, 3.5 to 5 kg per sq ft of built-up area.

1Where 4 kg comes from

Steel makers' guides give 3.5 to 5 kg per sq ft of built-up area for an RCC house. That spreads the footing mesh, column cages, beams, lintels and slab over the floor area. It is a budget figure for the house.

2What the roof takes

A slab is a thin sheet of mesh. Bar for bar, a 1000 sq ft roof comes to 1.3 to 1.4 tonnes with the top layer and allowance in our example. The bottom mesh alone is 0.6 to 1.1 tonnes, depending on bar size and spacing.

3Why it matters

Order 4 tonnes for the roof and about 2.6 tonnes sits on site, rusting through the monsoon, with your money in it. Order from a bare-mesh figure and you run short on dhalai day, with the mixer booked.

Whole-house steel, stage by stage: how much sariya a house needs. Quick house estimate: sariya calculator.

What is in a slab

Two layers of bars, held at the right height

A plain house slab (lenter) has a bottom mesh across the whole roof and a second, top layer only where the slab sits on beams and walls. Know the four parts and you can read any drawing and check any quotation, ours included.

Section through the slab at an inside beam
Cross-section of a roof slab over a beam A 125 mm slab resting on a beam. Main bars at the bottom on 20 mm cover blocks, distribution bars tied on them. Over the beam, top bars sit on bent-bar chairs near the top face and run about a quarter of the room span into each room, with their ends bent down. The beam below has its own bars and rings. Shuttering and props under the slab. top face pulls apart over the beam ≈ ¼ span≈ ¼ span 1 2 3 4 5 6 1 Main bar, bottom 2 Distribution bar, tied on it 3 Cover block, 20 mm 4 Chair: a bent bar that holds the top layer up 5 Top bar over the beam, ends bent down 6 Beam, with its own bars and rings Slab drawn 125 mm thick, a usual figure for house roofs.
Not to scale. Lengths of top bars and the size of the beam come from your drawing.

Main bars

The bottom layer, across the short side of each room, because a slab bends most across its short span. They do most of the carrying. If a room's long side is more than twice its short side, the slab works one way and these bars carry almost everything (standard figure, IS 456).

Distribution bars

Laid at right angles over the main bars and tied at every crossing. They hold the main bars at their spacing, spread a point load, and stop shrinkage cracks. Most Bihar rooms (10 × 12, 12 × 14 ft) are close to square, so they are two-way slabs and these bars work too.

Top bars at supports

Over a beam or wall the slab bends the other way and the top face pulls apart. So a second layer goes near the top there, reaching into each room. Some drawings bend up (crank) every other bottom bar instead; part of the top steel then comes from the bottom bars.

This is the layer bare "mesh" sums leave out, and the one trodden flat during a careless pour.

Cover and chairs

Cover blocks lift the bottom bars 20 mm off the shuttering (IS 456, mild exposure) so concrete wraps the steel and it does not rust. Chairs hold the top layer up to its height. Neither adds much weight, but leaving them out wastes the steel you paid for.

Limits you can check on the shuttering

CheckLimit
Gap between main barsIS 456, 26.3.3: 3 × effective depth, or 300 mm if less. For a 125 mm slab, 300 mm.≤ 300 mm
Gap between distribution barsIS 456, 26.3.3: 5 × effective depth, or 450 mm if less≤ 450 mm
Thickest bar for the slabIS 456, 26.5.2.2: one-eighth of slab thickness. 125 mm slab: 15 mm, so 12 mm fits, 16 mm does not.⅛ × thick
Least steel, each wayIS 456, 26.5.2.1: 0.12% of the slab section for TMT bars. 125 mm slab: 150 sq mm per metre.0.12%
Bottom coverIS 456, Table 16: mild exposure, inside the house20 mm

These are the code's outer limits, not a design. Drawings for houses usually sit well inside them, often 6 to 8 inches apart. If the bars on your shuttering are further apart than your drawing, stop and ask before the pour.

From spacing to kg

The method, on one room

Every slab sum, ours and your engineer's, is the same four steps. Here they are on a 12 × 10 ft room with 10 mm bars at 6 inches (150 mm) both ways.

Counting the bars in a 12 by 10 ft room 26 red bars, each 3.05 m long, run across the 10 ft side. 22 dark bars, each 3.66 m long, run across the 12 ft side. Together 159.7 m, times 0.617 kg per metre, is 98.5 kg. 12 ft = 3.66 m 10 ft = 3.05 m 26 bars × 3.05 m = 79.2 m 22 bars × 3.66 m = 80.5 m 159.7 m × 0.617 kg = 98.5 kg bottom mesh of one 120 sq ft room, about 0.82 kg per sq ft
  1. Count the bars one waySide length ÷ spacing, round up, add one for the end bar. The 12 ft side at 150 mm: 3.66 ÷ 0.15 = 24.4, round up to 25 gaps, so 26 bars.
  2. Multiply by the length of each barEach bar crosses the other side. 26 bars × 3.05 m = 79.2 m. The drawing adds the length that sits on the beam and any bend.
  3. Do the same the other way10 ft side: 3.05 ÷ 0.15 = 20.3, so 21 gaps and 22 bars × 3.66 m = 80.5 m.
  4. Metres × weight per metre159.7 m of 10 mm × 0.617 kg = 98.5 kg. Then add the top bars and the allowance for laps and cut ends, as in the full example below.
kg per metre = D × D ÷ 162, with D the bar size in mm. It comes from steel's weight (7,850 kg per cubic metre). 10 mm: 100 ÷ 162 = 0.617 kg.

Standard weight per metre

BarPer metreOne 12 m barWeight check, 12 m bar
6 mm0.222 kg2.66 kg2.48–2.85 kg±7%
8 mm0.395 kg4.74 kg4.41–5.07 kg±7%
10 mm0.617 kg7.40 kg6.89–7.92 kg±7%
12 mm0.888 kg10.66 kg10.12–11.19 kg±5%
16 mm1.58 kg18.96 kg18.01–19.91 kg±5%

Standard weight per metre and the allowed difference, from IS 1786. A bar much lighter than this is thinner than its label. Full chart: sariya weight per metre.

The 1000 sq ft chhat

A whole roof, worked out bar by bar

A 40 × 25 ft roof (1000 sq ft) over six rooms, with one beam down the middle and two across. Two versions, one in 10 mm only and one with 12 mm main bars. It shows the method; your own spacing comes from your drawing.

The roof in the example
Plan of the 40 by 25 ft roof slab A 40 by 25 ft slab over six rooms of about 13 by 12.5 ft. Outer beams along the 130 ft edge, inner beams 90 ft in all: one along the middle, two across. Yellow bands along every beam mark top bars: 2.2 m bars over inner beams, 1.0 m bars at the outer edge. Main bars run across the 25 ft way. 13 × 12½ ft13 × 12½ ft13 × 12½ ft 13 × 12½ ft13 × 12½ ft13 × 12½ ft 40 ft = 12.19 m 25 ft = 7.62 m Inner beams: 90 ft · outer edge: 130 ft Top bars: 2.2 m over inner beams, 1.0 m at edges Main bars run across the 25 ft way Rooms near square, so two-way slabs. Bars drawn fewer than real.

Version A: 10 mm at 6 inches both ways

PartBarsMetreskg
Main bars, 10 mmacross 25 ft, spaced along 40 ft83 × 7.62 m632.5390
Distribution bars, 10 mmacross 40 ft, spaced along 25 ft52 × 12.19 m634.0391
Top bars over inner beams, 10 mmabout 1 m into each room184 × 2.2 m404.8250
Top bars at outer edges, 10 mminto the room and bent down into the beam265 × 1.0 m265.0164
Laps, bends and cut endsusual allowance, 10%—193.6119
Total, 10 mm178 bars of 12 m2,129.91,314

Version B: 12 mm main bars at 6 in, 10 mm distribution at 8 in

PartBarsMetreskg
Main bars, 12 mm83 × 7.62 m632.5562
Distribution bars, 10 mm40 × 12.19 m487.7301
Top bars, 10 mmsame as version A449 bars669.8413
Laps, bends and cut endsusual allowance, 10%—179.0128
Total58 bars of 12 mm (618 kg) + 107 bars of 10 mm (786 kg)165 bars1,969.01,403

Rounded to the kg. Top bars use the same 6 inch spacing as the main bars. The 10% covers the lap where a 12.19 m bar is made from a 12 m bar, the bends, and ends too short to use.

The bottom mesh alone, for other spacings

Bars, same 40 × 25 ft roofkgPer sq ft
10 mm at 8 in (200 mm) both ways5920.59
10 mm at 6 in (150 mm) both ways7810.78
12 mm at 6 in main + 10 mm at 8 in8620.86
12 mm at 6 in both ways1,1251.12

One layer, no top bars, no allowance. Add the top layer (about 413 kg in this layout) and 10% before you order. Your own sizes: the calculator just below, or the sariya calculator for the whole house.

Your slab

Put in your roof and your drawing's bars

Same method as the tables above. It gives kg, 12 m bars and binding wire. Take the bar sizes and spacing from your drawing; the defaults are version A.

Main bars (across the short side)
Distribution bars (the long way)
Top bars over beams and walls

Inner beams: add up the lengths of every beam or wall under the slab inside the outer edge. Top bars are taken at the main-bar spacing, 2.2 m long over inner beams and 1.0 m at the outer edge.

Roof area: — sq ft

Your steel list

Binding wire—Usual practice: 8 to 12 kg per tonne of sariya. More for close spacing.
Total sariya —
Material totalAsk rate
Send this list on WhatsApp

Includes 10% for laps, bends and cut ends. Billed by weighed kg at today's rate (sariya rate). Your engineer's bar list replaces this estimate. Footings, columns and beams: sariya calculator.

Ordering in the shop's units

Kg on the bill, 12 m bars on the truck, bundles in the yard

Your list is in kg. The truck carries 12 m bars. The mill ties them in bundles. Here is how the three match, so the order is right the first time.

How one 12 m bar is used
Cutting plan for 12 m bars First bar: a 7.62 m main bar, then from the 4.38 m left over, one 2.2 m top bar and two 1.0 m edge bars, leaving 0.18 m scrap. Second: a 12.19 m distribution bar is one 12 m bar plus a 0.69 m piece overlapped by about 0.5 m. Bar 1: main bar, and its leftover becomes top bars main 7.62 m 2.2 m 1.0 + 1.0 m 0.18 m scrap 12 m Bar 2: a 12.19 m bar needs a lap one 12 m bar lap ≈ 0.5 m, tied + a 0.69 m piece from a cut end Cut ends become top bars, so little is wasted. The 10% covers laps like this and the last scraps.
Lengths from version A. Lap length is your engineer's figure; about 50 times the bar size is what masons often use, which is 0.5 m for 10 mm. More in lap length.

Kg: what you pay for

Sariya is billed by weighed kg, with GST shown on the bill. Two bars of the same size can differ a little in weight, so weight is the fair unit. Watch the weighing; that is the one number nobody argues about later.

12 m bars: what you count on site

Divide total metres by 12 and round up: version A is 178 bars of 10 mm. Count them when they are unloaded. If a sample bar weighs less than the check column in the weight table, tell us before it goes on the shuttering.

Bundles: how the mill ties them

Thin sizes come with more bars per bundle than thick ones, and the count differs from maker to maker. Websites quote different counts for the same size for this reason. Order in kg or bars, not bundles. Our counted bundles, size by size: bars in a bundle.

Cutting, delivery and the wire

A 12 m bar does not turn into many village lanes, so ask if you want bars cut to your lengths. Cutting and delivery are charged separately; ask for the amount for your site, see delivery. Order binding wire with the steel, about 11 to 17 kg for these slabs, so it comes on the same truck.

What goes wrong

Where slab steel is lost after you have paid for it

Buying the right kg is half of it. These four happen on site, on dhalai day or just before, and none of them shows until the slab is old.

DRAWN: 6 IN LAID: 10 IN

Spacing opened up to save bars

You see later: sagging, cracks underneath

Five bars where seven were drawn saves a few kg and costs the slab its strength. Check the spacing with a tape before the pour, against the drawing.

TOP BARS TRODDEN DOWN

Top bars stepped flat in the pour

You see later: cracks along the beam lines on the roof

A top bar pushed down to the bottom does nothing. Put chairs under it, lay walking planks, and have someone lift it back as the concrete goes in.

NO COVER BLOCKS underside, a few years later

Bars lying on the shuttering

You see later: rust lines and flakes under the roof

With no cover the bottom bars have no concrete under them and rust in the damp. 20 mm cover blocks every metre or so, both ways, cost very little.

ALL IN ONE LINE STAGGERED

Every lap at the same place

You see later: one crack line across the slab

Where bars are joined, the slab leans on the lap. Put all of them in one line and you have built a weak line. Stagger them, and keep them away from the middle of the room.

Send photos of the sariya on WhatsApp before dhalai and we'll check them with you. The full list: dhalai checklist.

Questions people ask us

Short answers

1000 sq ft chhat mein kitna sariya lagega?

In our worked example, a 40 × 25 ft roof with 10 mm bars at 6 inches both ways, top bars over the beams and 10% for laps and cut ends: about 1,314 kg. With 12 mm main bars, about 1,403 kg. Your drawing's sizes and spacing change it; the calculator above takes them.

Is 4 kg per sq ft right for a slab?

No. 3.5 to 5 kg per sq ft of built-up area is the figure for a whole RCC house, footings to roof. The roof slab alone came to about 1.3 to 1.4 kg per sq ft in our example, top layer included.

Lenter mein kitne mm ka sariya lagta hai?

House slabs are usually drawn in 10 mm and 12 mm, sometimes with 8 mm distribution bars. IS 456 limits the bar size to one-eighth of the slab thickness, so 15 mm for a 125 mm slab. Your drawing names the size. Size by size for the whole house: which mm sariya where.

6 inch or 8 inch spacing?

Whatever the drawing says. The code's outer limits are 300 mm for main bars and 450 mm for distribution bars in a normal house slab, and house drawings usually sit well inside them. Every inch more between bars is less steel in the slab, so never open it up on site.

How many 12 m bars, and how many bundles?

Divide total metres by 12 and round up. Version A is 178 bars of 10 mm; version B is 58 of 12 mm and 107 of 10 mm. Bars per bundle differ by size and maker, so we bill by weighed kg. Our counts: bars in a bundle.

How much binding wire for the slab?

Usual practice is 8 to 12 kg per tonne of sariya, so about 11 to 17 kg for a 1000 sq ft slab like ours. Close spacing means more crossings and more wire. More in how much binding wire.

Why are extra bars needed on top over the beams?

Over a beam or wall the slab bends the other way, so the top face pulls apart. Bars near the top, held up on chairs, take that pull. Leave them out, or let them get trodden flat, and cracks open along the beam lines on the roof.

Abhishek Ranjan
Diploma Civil Engineer, Tashya Ventures

Civil engineer at our Reva Road store, Muzaffarpur. The bar counts on this page were worked through by hand and checked against IS 456 and IS 1786 on 12 Nov 2026. The example shows the method; it is not a design for your house. Your engineer's drawing and bar list decide the steel.

Where the numbers come from

  1. BIS, IS 1786:2008, high strength deformed steel bars: nominal mass per metre (6 mm 0.222, 8 mm 0.395, 10 mm 0.617, 12 mm 0.888, 16 mm 1.58 kg) and the allowed mass difference (±7% up to 10 mm, ±5% over 10 to 16 mm).
  2. BIS, IS 456:2000, plain and reinforced concrete: 26.3.3 bar spacing in slabs (3d or 300 mm, 5d or 450 mm), 26.5.2 least steel 0.12% and thickest bar one-eighth of the slab, Table 16 nominal cover 20 mm for mild exposure; one-way slab where the long side is more than twice the short side.
  3. JSW Neosteel, How much steel is required for a house?: 3.5 to 5 kg per sq ft of built-up area for a whole house.
  4. Worked example: our own count for a 40 × 25 ft slab, method as shown. Top bar lengths (about a quarter of the room span into each room), 10% allowance, 50 × bar size laps and 8 to 12 kg of wire per tonne are usual practice, labelled as such.
  5. Tashya Ventures store: Tata Tiscon 6, 8, 10, 12, 16 mm in stock; sariya billed per kg; cutting and delivery charged separately.

Send us your slab drawing

Send a photo of the drawing or just the roof size and bar spacing. We'll send back kg, bars and wire, with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com