हिंदी Call90310 74624
Home›Guides›Putty
Putty guide · coats

How many coats of putty? Two thin ones, and a third is usually the wrong fix

The short answer
  1. Coat 1 fills
  2. Coat 2 smooths
  3. Light sanding, wipe dust
  4. Primer

New plaster takes two coats of putty. The first fills pores and trowel marks; the second gives the smooth white face the paint sits on. Both together stay under 1.5 mm. If the wall still shows dips after two coats, the answer is to level the wall, not to add a third coat.

2 coats
On new plasterBirla White, JK and Asian Paints all describe two.
1.5 mm
Both coats togetherBirla White and Asian Paints. About two bank cards stacked.
3–6 h
Between coatsBirla White: 3 h or more. JK: 4–6 h. Overnight before sanding.
Two coats, magnified
Magnified section of two putty coats on plaster Cement plaster has pores and trowel marks on its face. Putty coat 1 fills them and leaves a nearly flat skin. Coat 2 is a thin flat white face. Both coats together are no more than 1.5 millimetres, about two bank cards stacked. 2 Coat 2: the finish thin, flat, white; paint sits on this 1 Coat 1: the filler fills pores, pinholes, trowel marks Cement plaster cured, dry, wetted just before coat 1 ≤ 1.5mm both coats How thin is 1.5 mm? two bank cards, edge on (0.76 mm each). Thicker = cracks.
Not to scale: the putty is drawn far thicker than it is. Limit: Birla White's WallCare guide and the Asian Paints TruCare sheet both give 1.5 mm for two coats.
Two coats, two jobs

What each coat does, and what it can't do

Putty is a skin over the plaster, not a filler for a bad wall. Every coat goes on thin.

1Coat 1 fills

Spread thin with the blade, from the bottom up as Birla White suggests for WallCare. It fills pores, pinholes and trowel marks so the wall is nearly flat. Birla White is plain about it: keep it thin and even, don't try to cover big unevenness in one thick go.

2Coat 2 finishes

Once coat 1 is dry and loose bits are knocked off, coat 2 goes on just as thin. It gives the smooth, white face. Birla White says the second coat should not be thicker than it needs to be: the 1.5 mm limit is for both coats added together.

3Then sand, dust, primer

After it dries overnight, a light sanding with fine paper, then every bit of dust wiped off. Primer goes over the putty before paint, never paint straight on putty. The full order is on our putty, primer, paint guide.

Can one coat do? Birla White's own WallCare FAQ says 1–2 finishing coats, depending on the wall. One coat is enough only where the surface is already smooth, such as a sound painted wall being repainted (putty on an old painted wall). On new cement plaster, plan for two.

Waiting and sanding

Two coats take a day and a morning

The makers give different waiting times. These are brand figures for their own putty, not one rule. Where they differ, we go by the longer wait, and by touch: a putty coat that still feels cool is still wet.

Two coats of putty, step by step Day 1: wet the wall at 9, coat 1 at 9:30, wait 3 to 6 hours, knock off loose bits at 2 pm, coat 2 at 2:30, dry overnight. Day 2: light sanding with fine paper at 9, wipe off dust, primer at 10. DAY 1DAY 2 9:009:302 pm2:309:009:4510:00 1 2 Wet the wall Putty, coat 1 Knock off loose bits Putty, coat 2 Light sanding Wipe off all dust Primer damp, no water running (Birla White) thin; fills pores and trowel marks wet sponge, the blade, or fine emery thin again; both coats ≤ 1.5 mm fine paper, No. 320 or finer; never coarse dry cloth or brush; primer sticks to dust then two coats of paint wait 3–6 h (Birla White ≥ 3 h · JK 4–6 h) dries overnight, 10–12 h (Birla White · JK says 2–3 days before paint for its putty)
StepWait
Coat 1 to coat 2Birla White WallCare: at least 3 h · JK WallMaxX: 4–6 h · Asian Paints TruCare: 6–8 h3–6 h
Coat 2 to sanding and primerBirla White: "preferably overnight", 10–12 h10–12 h
Putty to paint, JK's figureJK WallMaxX page: let the wall dry 2–3 days before paint2–3 days
Water curing after puttyBirla White and Asian Paints: not neededNone
Mixed putty, use withinBirla White: 3–3.5 h. More on mixing putty3 h
In the monsoon, add time. Recoat times on the sheets are for mild, dry air (Asian Paints quotes 25°C and 50% humidity). In Muzaffarpur from July to September, give each coat overnight and press a knuckle on it before the next one: cool or soft means wait. More on putty drying time.
Which sandpaper number
Sandpaper numbers from coarse to fine A strip from coarse number 100 to fine number 500. 100 to 180 is for rust, old enamel and sanding plaster before putty. 320 and finer is for putty: Birla Opus names 320, Birla White says no coarser than 500 for the last pass on WallCare. 100150180220320400500 COARSE FINE Not for putty rust, old enamel; plaster before putty (Asian Paints: 180) For putty Birla Opus sheet: No. 320 Birla White, last pass: waterproof, 500 or finer
Coarse paper cuts through the putty film and weakens its water resistance (Birla White); Asian Paints also warns against sanding putty hard. Sand gently, wear a mask, then dust off. Paper: sandpaper.
When a painter asks for a third coat

Look at why. A full third coat is rarely the answer

A third coat sounds like extra quality. On the wall, it is extra thickness, and thick putty cracks. Here is what to do instead, by what you see after coat 2.

FILL THESE SPOTS ONLY

Pinholes, blade lines, a rough patch

Do: spot-fill, not a full coat

Put a thin dab on just those places, let it dry, sand it flush. Nerolac's guide also allows touch-ups in patches on old, uneven walls. The rest of the wall stays at two coats.

GAP > 1.5 MM straight aluminium patti or level LEVEL FIRST, THEN 2 COATS

Dips and waves you can see in side light

Do: level the wall, then two coats

Hold a straight patti on the wall. If the gap under it is more than putty's whole 1.5 mm, putty can't fill it. Birla White says WallCare "is not meant to be used as levelling material". Use its levelling putty as the first coat for shallow dips, or Levelplast for deeper ones, then WallCare.

3 COATS

"One more coat for strength"

You get: fine cracks, then flakes

A thick layer dries on the outside first while the inside is still wet, and it cracks (Birla White's list of putty mistakes). Whiteness and strength come from primer and paint, not more putty. If it has happened: paint lifting after putty.

How thick

Putty is a skin. Levelling is a different product

Drawn to the same scale
Putty and Levelplast thickness compared to scale At the same scale: one bank card is 0.76 mm; two coats of putty at most 1.5 mm; one layer of Levelplast at most 6 mm; Levelplast in all at most 20 mm, in layers. Bank card 0.76 mm Putty, both coats together ≤ 1.5 mm Birla White, Asian Paints Levelplast, one layer ≤ 6 mm Birla White Levelplast, all layers ≤ 20 mm 05101520 mm Three coats of putty still don't fill a dip that needs Levelplast.
Levelplast figures from Birla White's Levelplast page: up to 20 mm, laid in steps of no more than 6 mm. Levelplast does not replace putty; WallCare still goes on top.

Two makers give the same limit: Birla White for WallCare, and Asian Paints for TruCare, 1.5 mm for both coats together. Neither gives a separate figure for each coat. In practice the first coat carries a little more, because it fills the pores; the second is a thin skim.

Why thicker is worse

Thick putty dries on the face first while the inside stays wet. The face then cracks, and paint over it flakes. Birla White lists "applying a very thick coat" among its common putty mistakes.

If the wall needs more than 1.5 mm

  • Shallow dips over a wide area: Birla White's FAQ names its levelling putty (WallCare MF) as the first one or two coats, then one or two of WallCare. We order it for you.
  • Deeper hollows, wavy plaster, patchwork: Levelplast, up to 20 mm in layers of 6 mm at most, then two coats of putty.
  • Badly out of line: that is the mason's plaster to fix, before any putty.

Check it on site

Two quick tests. The straight-edge test (above). And the bag count: two thin coats use a known amount of putty per square foot, so an order far above it means thick coats. Try it in check the bags below.

Can putty cover cracks?

Hairline cracks only. Everything else gets filled first

All three makers say the same thing. Asian Paints' sheet says not to use its putty to fill cracks. JK says fill cracks and holes with a cement-sand mix or filler first. Birla White says significant cracks must be repaired before putty.

HAIRLINE

Fine lines in the plaster, often a net

Putty covers these

Shrinkage lines thinner than a hair. Brush the dust out of them, wet the wall, and the two coats of putty fill them in the normal way.

OPEN CRACK putty on top, after it driescut into a V, fill with filleror cement-sand / SBR mortar

A crack you can push a card edge into

Fill it first, then putty

Open it into a V, dust it, fill it with crack filler or a cement-sand mortar (SBR in the mix helps it grip), let it dry, then putty. Which filler for which width: putty vs crack filler · cracks before painting.

DIAGONAL, WIDER AT ONE END

Diagonal, wider at one end, or keeps coming back

Don't hide it under putty

Cracks from window and door corners, through the wall, or ones that reopen after filling, have a cause that putty won't stop. Send photos on WhatsApp and we'll check them with you. How to tell: structural crack or plaster crack.

Is putty necessary?

Yes for a smooth emulsion wall. Not for every wall

Birla White itself says putty is not mandatory for every paint system. It decides how the paint looks, so it matters most where you'll see it. The full comparison, with what skipping saves: putty or no putty.

Use two coats

Inside rooms on new plaster, with emulsion paint
  • Drawing room, bedrooms, anywhere you want a smooth, even finish.
  • Washable emulsions show every mark on the wall underneath; putty hides them.
  • WallCare putty, then primer, then paint.

You can skip it

Budget walls, outside walls, store rooms
  • Cement paint or distemper on a tight budget: primer on plaster, then paint. Emulsion or distemper.
  • Outside walls: Birla Opus exterior sheets only ask for holes to be filled. Putty outside, if any, is Waterproof putty.
  • Repaint of a sound wall: no full coat, only bad spots. Repainting old walls.

Wait before any putty

Damp patches, seelan, white salt
  • No number of coats stops water. Find and stop the leak, then let the wall dry fully; test by touch and colour, usually a few weeks after the leak is fixed.
  • Then Waterproof putty in place of WallCare. Putty on a damp wall.
Check the bags

How much putty two coats should take

Put in your room. Two thin coats on smooth plaster use a known amount. An order far above it means coats are going on thick, or a third coat is planned. Ask why before you buy.

Area to putty: — sq ft (door 3×7 ft, window 4×4 ft taken off)

Two coats should take

Smooth new plaster—17–20 sq ft per kg for two coats (Birla White, WallCare)—
Rough plaster—10–15 sq ft per kg: Asian Paints' figure for rough masonry, up to 1.5 mm in two coats
Asked for more than this?—Then the putty is going on thicker than 1.5 mm, or as three or four coats. Ask the painter why.
Ask today's price on WhatsApp

WallCare packs: 1, 5, 20, 40 kg. Today's price: putty rates. Whole house: how many bags of putty.

Questions people ask us

Short answers

How many coats of wall putty are required? (putty kitne coat)

Two thin coats on new plaster. The first fills pores and trowel marks, the second gives the smooth white face. Birla White, JK and Asian Paints all describe a two-coat job, and Birla White and Asian Paints cap both coats together at 1.5 mm.

When is a third coat needed?

Almost never as a full coat. Pinholes or blade marks left after coat two are filled as spot patches. Dips and waves need levelling first (Birla White's levelling putty, or Levelplast), then the usual two coats. A third full coat pushes the putty past 1.5 mm, and thick putty cracks.

Is one coat of putty enough?

On new cement plaster, no. On a smooth surface, such as a sound old painted wall that has been sanded, one skim coat can do; Birla White's FAQ allows 1–2 finishing coats depending on the wall. See putty on an old painted wall.

How thick should each coat be?

Birla White and Asian Paints give the limit for both coats together, 1.5 mm, not for each coat. The first coat takes a little more because it fills the pores; the second is a thin skim. If the wall needs more than that, it needs levelling, not putty.

Should wall putty be sanded?

Yes, lightly. Between coats, a wet sponge, the putty blade or fine waterproof emery knocks off loose bits (Birla White). After the last coat, sand gently with fine paper: the Birla Opus sheet names No. 320, and Birla White's WallCare guide says no coarser than 500. Coarse paper damages the putty. Then wipe off all the dust before primer.

Can wall putty cover cracks?

Only hairline cracks. Asian Paints' sheet says not to use putty to fill cracks, JK says to fill cracks with a cement-sand mix or filler first, and Birla White says significant cracks must be repaired before putty. A crack that is diagonal, wider at one end or keeps coming back needs its cause found; send photos on WhatsApp and we'll check them with you.

Is putty necessary before painting?

For a smooth emulsion finish on new plaster, yes. For a cement paint or distemper wall on a budget, no; the paint goes on primed plaster. Birla White itself says putty is not mandatory for every paint system. More in putty or no putty.

How long between two coats of putty?

Birla White says at least 3 hours for WallCare, JK says 4–6 hours for its putty, Asian Paints 6–8 hours for TruCare. After the last coat, overnight (10–12 hours, Birla White) before sanding and primer. In humid weather, longer. Details: putty drying time.

Does putty need curing with water?

No. Birla White and Asian Paints both say their putty needs no water curing. The wall is wetted before the first coat, without water running down it.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint Engineer at our Reva Road store, Muzaffarpur. Every number on this page was checked against the maker's own page or sheet on 12 Nov 2026. Where the makers give different figures, the page shows each one with its name.

Where the numbers come from

  1. Birla White, Wall putty work: step-by-step process (25 Sep 2026): two coats, thin first coat bottom to top, at least 3 h between coats, 10–12 h after the last, 1.5 mm in all, fine waterproof emery and no coarse sanding, remove dust, putty is not for major cracks, not mandatory for every paint system, 17–20 sq ft/kg.
  2. Birla White, WallCare putty page (FAQ): 1–2 coats of levelling putty (MF) for major undulation, then 1–2 coats of WallCare; WallCare is "not meant to be used as levelling material"; pre-wet; no curing.
  3. Birla White, Application process for WallCare putty: after the second coat, waterproof emery of not less than 500, no harsh rubbing.
  4. Birla White, Common wall putty mistakes: thick single coats crack because the face hardens before the inside.
  5. Birla White, Levelplast page (FAQ): up to 20 mm, in steps of at most 6 mm; not a substitute for WallCare.
  6. JK Maxx Paints, WallMaxX putty page: fill cracks and holes with cement-sand or filler first, 4–6 h between coats, 2–3 days before paint, 10–40°C.
  7. Asian Paints, TruCare wall putty information sheet: 2 coats, 10–15 sq ft/kg on rough masonry for up to 1.5 mm in 2 coats, 6–8 h recoat at 25°C and 50% humidity, plaster sanded with 180 before putty, do not sand putty vigorously, do not use putty to fill cracks, no water curing.
  8. Birla Opus, Calista Ever Wash Shine information sheet: putty sanded with No. 320.
  9. Nerolac, Precautions for applying wall putty: two thin coats, touch-ups in patches on uneven old walls, fine emery, a mask when sanding.

Not sure about your wall?

Send a photo of the wall in side light on WhatsApp. We'll tell you whether it needs two coats, levelling first, or crack filling, with today's price.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com