हिंदी Call90310 74624
Home›Guides›Putty
Putty guide · damp walls

Putty on a damp wall: why it peels, what to fix first, and which putty to use after

The short answer

Putty on a wall with seelan comes off, every time. Not because the putty was bad, but because water is still coming into the wall from behind. No putty stops that, not even waterproof putty. Do it in this order:

  1. Find the water
  2. Stop it there
  3. Let the wall dry
  4. Salt? Salt Seal
  5. Waterproof putty × 2
  6. Primer
  7. Paint × 2

Only two kinds of damp need nothing more than waterproof putty: damp air in the monsoon, and rain on an outside wall once that wall is sealed from outside. Everything else is a leak, and the leak gets fixed first.

Weeks
Drying after the fixUsually a few weeks. Test by touch and colour, not by the calendar.
2×
Water resistance, not a damBirla White's claim for WallSeal over normal putty. It resists damp; it can't hold back a leak.
500+
Sandpaper grit, gentlyRough paper breaks waterproof putty's water repellence, Birla White warns.
What happens inside a seelan wall
Why putty comes off a damp wall A wall cut open. Water keeps entering the brick from behind. It carries salt out of the brick and sand into the plaster. Water and salt collect behind the putty, the paint bubbles, and lower down the putty has fallen off in a flake, taking the paint with it. 1 2 3 4 Water keeps coming It carries salt Paint bubbles Putty falls off from the roof, a pipe,rain or the ground out of brick and sand water and salt behind it and takes the paint BRICK DAMP PLASTER ROOM
Not to scale. Water moving out of the wall gathers behind the putty and the paint film. Salt it carries dries there as crystals. Waterproof putty slows water down; it does not stop water that keeps arriving.
Why the putty lets go

Three things push putty off a damp wall

Painters often blame the putty brand. The real cause is almost always behind the putty.

1It never gets a grip

Putty is white cement and polymer. It needs a firm, dry-backed surface to set onto. A wall that stays wet from inside keeps the putty soft at the back, so it holds for a few weeks and then lets go.

2Salt grows behind it

Water carries salt out of the brick and sand. Where the water dries, the salt stays as crystals, and crystals growing behind putty push it off. Birla White says ordinary putty is porous, so salt passes into it. More: white salt on walls.

3Paint traps the water

Paint is a film. Water coming out of the wall collects under it as a bubble. When the bubble breaks, the putty underneath, already soft and salty, comes away with it.

✓Pre-wetting a dry wall
A dry wall wetted on the surface just before putty: only a thin skin is damp, the inside is dry, and the putty grips. dry inside WALL Only the skin is damp a splash just before putty, no puddles putty sets and grips the dry wall
✕A wall with seelan
A wall with seelan: wet all the way through, water keeps moving to the surface with salt, and the putty lifts off. wet right through WALL Wet all the way through water and salt keep coming, for weeks the putty never gets a grip and lifts

The confusing part: Birla White asks you to wet the wall before putty, for WallSeal as much as for WallCare. That is a splash on a dry wall so the plaster doesn't suck the water out of the paste. A wall with seelan is the opposite: soaked from inside. Wetting is right; seelan is not.

Step 1 · find and stop the water

Will waterproof putty alone do? Only for two of these six

Match your patch to a card. Where it says fix this first, putty comes only after that repair. Not sure which it is? Seelan in the wall: the six causes.

Damp air in the monsoon

Spots in corners, walls and glass feel wet, no single patch
Waterproof putty is enough

Not a leak: moist air with nowhere to go. Air the room on dry days, run the exhaust fan, keep cupboards off the wall. Clean any black spots first: fungus on walls. Then waterproof putty, primer and paint.

Rain through an outside wall

Inside face of a wall the weather hits, worse after heavy rain
Enough, once the outside is sealed

Fix it from outside: fill cracks with Seal & Dry SBR mortar, put WP+200 in any new plaster, then Seep Guard Vertical or a Birla Opus exterior paint system. Inside, waterproof putty. Details: outside wall waterproofing.

Roof or parapet

Top floor, starts at the ceiling line, worse a day after rain
Fix this first

Clear the drains so no water stands, repair cracks with WP+200 in the mortar, coat with Weather Pro Hi-Flex. See roof and parapet joint.

Bathroom next door

Wettest right against the bathroom, worst after baths
Fix this first

Re-grout open joints and seal round the floor trap. If the floor is soaked: Seal & Dry SBR in the base coat and Hi-Flex under new tiles. See bathroom waterproofing.

A pipe inside the wall

Round patch on a pipe line, wet even in the May heat
Fix this first

A plumber's job. No coating holds back water under pipe pressure. Open the wall, fix the joint, replaster: leaking pipe joint.

Ground water (rising damp)

Band from the floor up to 2–3 ft, wavy line, white salt
Fix this first

Scrape the band back, coat the lower wall with Seep Blocker 2K, then Salt Seal and waterproof putty. In a house with no damp-proof course this can creep back: coatings slow it, they are not a new DPC. See plinth and DPC.

Steps 2 and 3 · dry, then clean back

After the repair: let it dry, then scrape back to hard plaster

This is the gap where most money is lost. The leak is fixed on Monday, the painter is back on Wednesday, and the wall is still full of water.

The order of work on a damp wall Find where the water comes from. Stop it at that place. Is the wall still getting wet? If yes, go back to finding the water. If no, let the wall dry, usually a few weeks. Is it dry to touch and even in colour? If no, wait. If yes: is there white salt? If yes, one coat of Salt Seal. Then two coats of waterproof putty, then primer and two coats of paint. YESNO NO: WAITYES YESNO Find where the water enters Stop it at that place roof · pipe · bathroom · wall · plinth Still getting wet? Let the wall dry usually a few weeks after the fix Dry to touch, even in colour? White salt? Salt Seal 1 coat, 1:1 Waterproof putty × 2 light pre-wet · both coats ≤ 1.5 mm Primer, then paint × 2 interior primer 1:1 · 4–6 h gaps

1Give it weeks, not days

After the leak is fixed the wall still holds water. How long it takes depends on how thick the wall is, how long it was wet and the weather. Usually a few weeks. Through the monsoon it can take longer; a dry spell in October–November or March–April is the best time to finish.

2Check by touch and colour

Dry plaster is one even, light colour, and the old patch feels as warm and dry as the wall around it. A darker ring or a cool, clammy feel means wait. For a firmer answer, tape a clear plastic sheet about a foot square tight over the old patch for 24 hours: drops under the sheet mean the wall is still giving out water (usual practice among painters, not a maker's figure). More: painting a damp wall.

3Scrape back to hard plaster

Old putty that got wet is soft or salty even when it looks fine. Scrape off everything loose, powdery or blistered, about a foot past the last mark, until the blade meets hard plaster. Brush the salt off dry; washing puts more water in.

4Tap for hollow plaster

Tap the plaster with a coin. A dull, hollow sound means it has come loose from the brick. Cut that patch out and replaster it, with WP+200 in the mortar (UltraTech: 200 ml per 50 kg bag of cement). New plaster then needs curing and drying before putty.

Where to scrape on a ground-floor wall
How far to scrape back A painted wall with a damp band from the floor up to a wavy tide line, flaking and white salt along it. A dashed red line marks the area to scrape: about one foot beyond the last mark, up and to the side. A coin taps the plaster: a hollow sound means that patch must be replastered. ≈ 1 ft ≈ 1 ft Scrape back to hard plaster red line: about 1 ft past the last mark brush the salt off dry, don't wash it Tap with a coin: hollow sound = replaster that patch
The 1 ft margin is usual practice: damp spreads a little past what you can see. Rising damp in Muzaffarpur houses usually stops 2–3 ft up; higher than that, look for a roof or pipe leak.
Step 4 · the putty

Which putty goes on a wall that has had seelan

All three are Birla White white-cement putties. The difference is how much water they let through.

PuttyMade forOn a wall that had seelanCoverage, 2 coatsPacks
WallCareordinary puttyDry inside wallsNo. Birla White calls ordinary putty porous: water and salt pass into it.17–20 sq ft/kg1, 5, 20, 40 kg
Waterproof puttyWallSealInside and outside walls that face rain, moisture and humidityYes, our pick, once the leak is fixed and the wall is dry. Birla White: 2× the water resistance of normal cement putty.16–19 sq ft/kgon a smooth wall40 kg on our shelf; 1, 5, 20, 30 kg we order for you
SaltBlockanti-salt puttyWalls that have shown white saltYes, where salt was the main trouble. Two coats in place of normal putty.17–20 sq ft/kg5, 40 kg: we order it for you

Wall with white salt

Ground-floor walls, walls after a flood
Brush off drySalt Seal × 1Waterproof putty × 2PrimerPaint × 2
  • AllDry Salt Seal is a primer that blocks salt, not a putty. Birla Opus: one coat, 1 L with 1 L water, then putty, primer and paint.
  • Or SaltBlock putty in place of waterproof putty. Full guide: white salt on walls.

Wall that was wet, no salt

After a roof, pipe or bathroom repair
Light pre-wetWaterproof putty × 2PrimerPaint × 2
Steps 5 to 7 · doing it

Waterproof putty, step by step

From Birla White's WallSeal instructions, with primer and paint from the Birla Opus sheets. Start only on a wall that has passed the dry check.

  1. Salt Seal, only if there was saltBrush the salt off dry. One coat of Salt Seal, 1 L with 1 L water.wait 4–6 h
  2. Clean and wet lightlyRemove dust and loose bits with a putty blade or wire brush. Wet the wall with a brush or spray just before the putty. No water standing or running.
  3. Mix1 kg putty into 360–380 ml clean water, stir 3–5 minutes (a machine stirrer is best), let it rest 5 minutes. Use it within 3 to 3½ hours. Never add extra water.
  4. Coat 1, thinWith a putty blade, evenly. Not on a wall hotter than 40°C: on outside walls, avoid the noon sun.when dry, wipe gently with a wet sponge
  5. Coat 2Both coats together no thicker than 1.5 mm. Putty is a skim, not a filler for dips.at least 3–4 h after coat 1
  6. Let it dryBirla White says preferably 24 hours, longer in damp weather, until it is fully dry.≈ 24 h
  7. Sand only if you must, and gentlyWaterproof emery paper of 500 or finer. Rough paper breaks the water repellence. Wipe the dust off.
  8. PrimerActivCoat Interior, 1 L with 1 L water, one coat over the putty.wait at least 4 h
  9. Paint, 2 coatsInterior emulsion. Not when humidity is above 90% (Birla Opus).4–6 h between coats
500 grit or finer: water beads

Sanded gently

The surface keeps its water repellence. Water stays on top.

Rough paper: water soaks in

Sanded hard

Birla White warns that rough emery breaks the water repellence. You paid for waterproof putty and sanded it off.

Primer over the putty, even though the bag says no. Birla White's WallSeal brochure says no primer is needed before paint. The Birla Opus paint sheets put a primer coat over putty before the paint. We follow the safer one: one coat of interior primer. It costs one thin coat and saves the paint from soaking in patchily.
A usual plan, once the wall is dryWhen
Salt Seal (if salt), then putty coat 1Coat 1 after the 4–6 h Salt Seal gapDay 1
Putty coat 2At least 3–4 h after coat 1; next morning is fineDay 2
Gentle sanding, primer, paint coat 124 h after coat 2, then 4 h after primerDay 3
Paint coat 24–6 h after coat 1Day 4
How much for your wall

Waterproof putty, Salt Seal, primer and paint for the damp wall

Put in the wall you are redoing. Quantities use the makers' coverage figures, low and high. Buy for the high number if the plaster is rough or was patched.

Area: — sq ft (take off doors and windows yourself if they are large)

Your list

Waterproof putty, 2 coats—16–19 sq ft per kg on a smooth wall (Birla White WallSeal)—
ActivCoat Interior primer, 1 coat—170–200 sq ft per litre on putty, litres from the can before water (Birla White)—
Calista Ever Wash Shine, 2 coats—130–150 sq ft per litre for 2 coats (Birla Opus)—
Material totalAsk rate
Send this list on WhatsApp

Waterproof putty: 40 kg bags on our shelf; smaller bags we order for you. This list is for the finish only; the repair that stops the water comes first. Prices are filled in from today's rate.

Questions people ask us

Short answers

Can I put putty on a damp wall?

Not on a wall that is damp from seelan. Water still coming from inside keeps the putty from gripping and brings salt that pushes it off. Stop the water, let the wall dry, then putty. A light wetting just before putty on a dry wall is different, and Birla White asks for it.

Can wall putty be applied directly on a wall?

On clean, sound, dry cement plaster, yes, after wetting it lightly as Birla White's instructions say. Not on a wall with seelan, white salt, loose old paint or hollow plaster: those get fixed first. On salt, a coat of Salt Seal goes on before the putty.

Will waterproof putty stop seepage? (seelan ka ilaj)

No. It resists damp much better than ordinary putty (Birla White claims twice the water resistance), so it suits walls that get humid air or rain splash. It cannot hold back water that keeps coming from a roof, pipe, bathroom or the ground. That needs the repair at the source.

How long after the leak is fixed can I put putty?

Usually a few weeks; there is no fixed number of days. Wait until the old patch is the same colour as the rest and feels dry and warm to the touch. A plastic sheet taped over it for 24 hours should stay dry underneath.

The WallSeal bag says no primer is needed. Why primer?

Birla White's brochure does say that. The Birla Opus paint sheets put a primer coat over putty before the paint. We follow the safer rule: one coat of interior primer, 1:1 with water. It stops the paint soaking in patchily.

Can I sand waterproof putty like normal putty?

Only gently, and only with waterproof emery paper of 500 or finer. Birla White warns that rubbing the last coat with rough paper breaks its water repellence. Normal putty is often sanded with No. 320; don't do that here.

My putty is already peeling. Do I redo the whole wall?

Scrape off everything loose, soft or blistered, about a foot past the last mark, back to hard plaster. Putty that is still hard and well stuck elsewhere can stay. Fix the water first. Other reasons paint lifts after putty: paint coming off after putty.

Can I use waterproof putty on every wall of the house?

Yes. Birla White makes it mainly for inside walls as well as outside ones. It costs a little more than WallCare, so most people use it on ground-floor walls, walls beside bathrooms and walls facing the rain, and WallCare on the rest.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint Engineer at our Reva Road store, Muzaffarpur. Every number on this page was checked against the maker's own sheet on 12 Nov 2026. Where two makers say different things, the page says so and follows the safer one.

Where the numbers come from

  1. Birla White, WallSeal Waterproof putty brochure: mainly interior walls as well as exterior surfaces exposed to rain, moisture and humidity; pre-wet a must; 1 kg + 360–380 ml water; use within 3–3.5 h; surface not above 40°C; wet sponge after coat 1; at least 3–4 h between coats; preferably 24 h before paint; no rough emery, 500 or finer only; 1.5 mm total; "no primer is required"; 16–19 sq ft/kg on a smooth surface.
  2. Birla White, WallSeal Waterproof putty page (FAQ): white cement, hydrophobic and silicone polymers; 2× water resistance over normal cement putty; 2 coats; no curing; 1.49–1.76 sq m/kg; packs 1, 5, 20, 30, 40 kg; 12-month shelf life.
  3. Birla White, Best wall putty for salt stains: ordinary putty is porous; and SaltBlock putty page: 2 coats, packs 5 and 40 kg.
  4. Birla White, WallCare putty page and Wall putty work: step-by-step: pre-wet, 17–20 sq ft/kg.
  5. Birla Opus, AllDry Salt Seal information sheet: find and stop seepage first; 1:1 with water, one coat; 80–100 sq ft/L; 4–6 h; inside followed by putty, primer, paint; packs 1, 4, 20 L.
  6. Birla Opus, Calista Ever Wash Shine and Style Color Smart sheets: primer over putty, 4–6 h between coats, no painting above 90% humidity, 130–150 and 120–140 sq ft/L for 2 coats; One Pure Elegance 140–160 sq ft/L.
  7. Birla White, ActivCoat Interior primer: 1:1 with water, 170–200 sq ft/L per coat on putty.
  8. UltraTech, Weather Pro brochure: WP+200 at 200 ml per 50 kg bag; Hi-Flex 14–15 sq ft/kg per coat. Birla White Seep Blocker 2K and Seep Guard Vertical pages.
  9. Drying checks, the plastic sheet test, the 1 ft scraping margin and the 2–3 ft rising-damp height: usual practice and what we see in Muzaffarpur houses, not makers' figures.

Not sure where the water comes from?

Send photos on WhatsApp and we'll check them with you: one close-up of the patch, one of the whole wall from floor to ceiling, and say which floor it is on.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com