हिंदी Call90310 74624
Home›Problems and fixes›Paint
Problem and fix · damp walls

Painting a damp wall: find the water first, then seal, putty and paint

The short answer
  1. Stop the water
  2. Let the wall dry
  3. Scrape to sound plaster
  4. Salt Seal, if salt
  5. Waterproof putty inside · WallFix 4 outside
  6. Primer and paint

No paint, putty or "damp-proof" coat holds back water that is still getting into the wall. Paint over seelan and it bubbles and peels within a season. Fix the roof, the pipe or the outside wall first. The coats only protect a wall that is already dry.

Weeks
Drying after the leak is fixedUsually a few weeks. Test by touch and colour, not by the calendar.
< 10
Moisture meter, green zoneWhat Birla Opus asks for before Salt Seal. Red zone: fix the water first.
4 days
No rain after outside workOpus exterior rule. WallFix 4 alone asks for 48 hours.
Four ways water reaches a wall
Where seelan comes from in a house A house cut open. 1: water standing on the roof leaks through a crack and stains the wall below the ceiling. 2: rain soaks through the outside wall and leaves a patch on the inside. 3: a leaking pipe beside a bathroom wets the wall. 4: groundwater rises through the plinth and leaves a band with a wavy tide line and white salt low on the wall. rain water standing on the roof pipe plinth: a DPC here should stop ground water groundwater: high in north Bihar 1 2 3 4
  1. 1Roof or parapet: patch high up, spreading down from the ceiling, worse after rain.
  2. 2Outside wall in rain: patch on a wall that faces the weather, after heavy rain.
  3. 3Bathroom or pipe: patch beside a bathroom or along a pipe, wet even in dry months.
  4. 4Ground (rising damp): a band low on the wall with a wavy tide line and white salt.
Each one has a different fix, and none of the fixes is paint. Building fixes in detail: seelan from foundation to roof.
Why the paint keeps coming off

Paint over seelan and you pay for the same wall twice

This is the most common money lost in a Bihar repaint. The wall looks fine for a few weeks, then the water wins.

Paint on a wet wall: fine in week 1, bubbles by month 2, peeling with white salt by month 6 WEEK 1MONTH 2MONTH 6 Looks fineBubblesPeels, white salt water still in the wallwater pushes the film offsalt lifts what is left

1Water pushes paint off

Paint is a thin film. Water moving out of the wall gathers behind it, lifts it as bubbles and peels it. Birla Opus says plainly not to apply WallFix 4 on wet or visibly damp surfaces.

2Salt comes out with it

Bricks, sand and groundwater carry salt. As the water dries at the surface it leaves white powder that pushes off putty and paint. Scraping it off does nothing while the water keeps moving. More: white salt on walls.

3"Waterproof" coats are not a dam

Waterproof putty and damp-proof basecoats protect a dry wall from getting wet again. None of them holds back a live leak from the roof, a pipe or the ground.

Step 1 · Find the water

Where the patch is tells you where the water comes from

Look at both sides of the wall and at what is above it. Then fix that first, with the product made for that place.

Low on the wall, ground floor

How to tell
A band from the floor up to about knee or waist height, with a wavy tide line and white powder. Often on both faces of the wall, worse after the monsoon or a flood.
Cause
Groundwater rising through the brick because the plinth has no damp-proof course (DPC), or it is broken.
Fix first
Scrape the damp band back to plaster. Coat the inside face with Birla White Seep Blocker 2K, then Waterproof putty. Building fixes at the plinth: seelan, foundation to roof.
Straight talk: in a house with no DPC this can creep back. A coating slows it down. It is not a new DPC.

High up, near the ceiling

How to tell
The patch spreads down from the ceiling or the top of the wall, darker after rain, sometimes dripping. Top-floor rooms and walls under a parapet.
Cause
Water standing on the roof, cracks in the slab or the parapet top, a blocked roof drain.
Fix first
Clear the drain and make sure the roof slopes to it. Repair cracks with mortar mixed with UltraTech Weather Pro WP+200, then coat the roof with Weather Pro Hi-Flex.

Beside a bathroom or along a pipe

How to tell
On the wall shared with a bathroom or kitchen, or along a pipe line. Wet even in the dry months; can grow after the tap or shower is used.
Cause
A leaking pipe joint, or water getting through the bathroom floor and the joints between floor and wall.
Fix first
Get the pipe repaired. In the bathroom: UltraTech Seal & Dry SBR in the base coat and Hi-Flex under the tiles.

Outside wall, after rain

How to tell
On the inside of a wall that faces the weather. It appears after heavy rain and fades in winter. Outside you see cracks and bare or chalky paint.
Cause
Rain soaking through cracked plaster, or old paint that no longer sheds water.
Fix first
Fill the cracks outside. If you replaster, add WP+200 to the plaster. Then AllDry WallFix 4 under Birla Opus exterior paint, as below.

All over, in corners, in the monsoon

How to tell
Black or green spots in corners and behind cupboards, drops of water on glass and cold walls, a damp smell. No single wet patch.
Cause
Moist air with nowhere to go (condensation). Not a leak.
Fix first
Air the room on dry days, run an exhaust fan in the kitchen and bathroom, keep cupboards a little off the wall. Clean the spots before painting: fungus on painted walls.
Step 2 · Before any coat

Wait until the wall is dry. Here is how to check

After the leak is fixed, the wall still holds water. There is no fixed number of days: it depends on how thick the wall is, how long it was wet, and the weather.

The plastic sheet test, seen from the side
Plastic sheet test: three results A clear plastic sheet taped to the wall for 24 hours. Drops between the wall and the sheet mean water is still coming out of the wall. Drops on the room side of the sheet mean damp room air. No drops on either side means the wall is ready. wallsheetroomwallsheetroomwallsheetroom ✕!✓ Drops underDrops on topDry both sides wall still wet:wait, find the waterdamp room air:air the room, test againready forthe next step
Tape a clear plastic sheet, about one foot square, tight on all four sides over the old patch. Look after 24 hours. Usual practice among painters; it costs nothing.

1Touch and colour

The old patch should feel as dry and warm as a sound part of the wall, and its colour should match the rest. This usually takes a few weeks after the leak is fixed, longer in the rains.

2The plastic sheet test

As in the drawing. Drops under the sheet mean water is still coming out of the wall. Wait, and check that the leak is really fixed.

3A moisture meter, if your painter has one

Birla Opus asks for the reading to be in the green zone, below 10, before Salt Seal. In the red zone, fix the source of the water before painting.

AllDry Salt Seal information sheet

4The weather

WallFix 4: not on a wet surface, not above 80% humidity, and no rain for 48 hours after. Opus exterior work: no rain likely for 4 days, between 10 and 40°C. October to March is the safe time outside. More: painting in the monsoon.

What we can and cannot promise

  • We cannot see inside your wall. No putty or paint holds back water that is still getting in.
  • In an older house with no damp-proof course, rising damp can return however good the paint is.
  • We don't make free site visits.
  • Send us photos on WhatsApp before you buy: the patch, the other side of the wall, and the roof or bathroom above it. We will look at them with you, say which cause it looks like, and what to buy.
  • Every product on this page can be ordered. If it is not on the shelf, we order it and tell you how long it takes.
Step 3 · Once the wall is dry

Then the coats: one system inside, one outside

First, the same preparation on both sides: scrape off everything loose, bubbled or powdery down to sound plaster, brush off the white salt dry, and fill the cracks.

Preparation, from the Birla Opus sheets

  • Cracks up to 3 mm: AllDry Crack Master paste. The WallFix 4 sheet allows it up to 5 mm and the Salt Seal sheet only 3 mm, so we use 3 mm. We can order it for you.
  • Bigger cracks and hollow plaster: cut out and repair with a polymer mortar. Opus names its AllDry Repair Master; a cement mortar with Seal & Dry SBR does the same job. Wide or growing cracks need a mason or engineer first.
  • Small holes and dents: cement putty, or white cement and fine sand 1:3 (Salt Seal sheet).
  • Outside, Opus recommends a pressure wash to clean the wall, then let it dry again. Algae: clean it off and rinse any bleach away fully.
  • New plaster, if you replastered: 28 days of curing with water first (both sheets), then let it dry.
Inside wall, after seelan
Layers for an inside wall that had seelan From the brick: dry plaster, Salt Seal only if there was salt, two coats of waterproof putty, primer, then two coats of washable paint facing the room. ROOM 1 2 3 4 5 6 Brick wallPlasterSalt SealWaterproof puttyWaterproof puttyPrimerPaint, coat 1Paint, coat 2 mason's workdry, scraped to soundonly if salt · 1 L + 1 L watercoat 1, thincoat 2 · sand, wipe dustActivCoat · 1 L + 1 L waterwashable sheen painte.g. Calista Ever Wash Shine
Not to scale. The Salt Seal sheet puts putty, primer and paint over it inside. No salt? Start with the primer instead, in the usual putty, primer, paint order.
Outside wall that lets rain in
Layers for an outside wall that let rain through From the brick: plaster, with WP+200 in it if replastered; AllDry WallFix 4 first coat thinned with 10% water; WallFix 4 second coat with no water; then two coats of Birla Opus exterior paint facing the weather. OUTSIDE · RAIN 1 2 3 4 Brick wallPlasterWallFix 4, coat 1WallFix 4, coat 2Exterior paintExterior paint mason's workWP+200 in it, if redone10% water · primesno water · 4–6 h latercoat 1 · Style, Calista, Onecoat 2 · 3rd on parapet tops No primer needed:WallFix 4 primes itself.
Not to scale. An outside wall with white salt but no rain soaking through: Salt Seal (1 L + 1 L water, one coat) in place of the two WallFix coats, then 2–3 coats of exterior paint. Neither sheet puts one under the other, so we don't stack them.
LayerHow, from the sheetThen wait
Leak fixedowner's rule for our customersDry by touch, colour and the sheet testweeks
AllDry Salt Sealinside or outside, walls with salt1 L + 1 L water, one coat. 80–100 sq ft per litre of Salt Seal. Use thinned paint within 24 h. Don't tint it.4–6 h
AllDry WallFix 4outside walls, parapets, chhajjasCoat 1 with 10% water, coat 2 with none. 40–45 sq ft per litre for the job. A sound wall being repainted: one coat without water.4–6 h
Waterproof puttyinside, in place of WallCareTwo thin coats, sand and wipe off the dust. Water and times as printed on the bag.bag
Primer, insideActivCoat Interior1 L + 1 L water, over the putty≥ 4 h
PaintBirla Opus emulsions2 coats inside, 2–3 outside, one extra on parapet tops and chhajjas4–6 h
Outside, after the last coatNo rain likely. WallFix 4 alone asks for 48 h; we use the Opus exterior figure.4 days

Where the Salt Seal sheet gives two coverage figures (100–120 sq ft/L on smooth, fully cured plaster; 80–100 in the application table), we use the lower one so you don't run short. The WallFix 4 web page says a 4-year warranty and its sheet "up to 5 years", depending on the top coat. Both Opus warranties need registration within 15 days of purchase and the full recommended Birla Opus system.

How much for your wall

Salt Seal, WallFix 4 and paint for the damp wall

Put in the size of the wall you are redoing, not only the patch: paint the whole wall so the colour matches. Low and high numbers come from the makers' coverage figures.

Area: — sq ft

Your list

Material totalAsk rate
Send this list and photos on WhatsApp

Litres are from the can, before water. Packs are the makers' sizes; prices are filled in from today's rate. The products for the leak itself (roof, pipe, plinth) are on the waterproofing page.

On our shelf for this job

The products, by step

Anything not on the shelf, AllDry Crack Master included, we can order for you: ask on WhatsApp for the time it takes. Today's prices: paint rates · waterproofing rates. All products for leaks: waterproofing.

Questions people ask us

Short answers

Can I paint over seelan? (seelan par paint kar sakte hain?)

No. Water still moving through the wall pushes the paint off as bubbles and peeling, and carries white salt out with it. Birla Opus says not to apply WallFix 4 on wet or visibly damp surfaces, and its Salt Seal sheet says to fix the source of water first if a moisture meter reads in the red zone. Stop the water, let the wall dry, then paint.

How long after fixing the leak can I paint?

Let the wall dry fully. Test it by touch and colour: the old patch should feel as dry and warm as a sound wall and match its colour. That usually takes a few weeks after the leak is fixed, longer in the monsoon. A plastic sheet taped on the wall for a day should stay dry underneath.

Does waterproof putty or "damp-proof" paint stop seelan?

No. They help a wall that gets damp now and then keep its paint, but they cannot hold back water that is still getting in from the roof, a pipe or the ground. That has to be fixed at the source, with the products in Step 1.

Do I need both Salt Seal and WallFix 4?

Usually one. Salt Seal is a sealer primer for walls with white salt, inside or outside: one coat, with an equal amount of water. WallFix 4 is a waterproofing basecoat for outside walls: two coats under exterior paint. Neither Birla Opus sheet puts one under the other, so we pick one per wall.

Can WallFix 4 go on an inside wall?

The Birla Opus product page mentions interiors in its FAQ, but the product information sheet names plastered vertical surfaces like parapets, sunshades and exterior walls, under Birla Opus exterior paint. We follow the sheet: WallFix 4 outside. Inside, use Salt Seal if there is salt, then waterproof putty, primer and paint.

Why not just put tiles or wallpaper over the damp patch?

The water does not stop, it moves. Covered up, it rises higher or comes out beside the tiles, and the wall behind stays wet. Fix the water first; then cover the wall with whatever you like.

What is seelan called in English?

Damp or dampness. Water coming through a wall is seepage, damp rising from the ground is rising damp, and the white powder it leaves is efflorescence.

Mr Mustafaa
Paint Engineer, Tashya Ventures

Paint, putty and waterproofing at our Reva Road store, Muzaffarpur. Every figure on this page was checked against the maker's own product sheet on 12 Nov 2026. Where the sheet and the maker's website disagree, the page says so and follows the sheet.

Where the figures come from

  1. Birla Opus, AllDry Wall Fix 4 information sheet (WF12002//2024): waterproofing basecoat for exterior vertical walls under Opus exterior emulsions; coat 1 with 10% water, coat 2 undiluted; 40–45 sq ft/L; 4–6 h recoat; cure new masonry 28 days; cracks up to 5 mm with Crack Master; not on wet or visibly damp surfaces, not above 80% humidity, no rain within 48 h, 10–40°C; 5 bar water pressure (internal test, EN 12390-8); elongation up to 100%; packs 1, 4, 10, 20 L; warranty up to 5 years by top coat.
  2. Birla Opus, AllDry Salt Seal information sheet (SS002/08/2024): alkali-block primer against efflorescence; 100% dilution with water, one coat; 80–100 sq ft/L (100–120 on smooth cured plaster); 4–6 h; inside followed by putty, primer, paint, outside by 2–3 top coats; moisture meter green zone below 10; wall pH below 10; cracks up to 3 mm with Crack Master; holes with white cement and sand 1:3; find and arrest seepage first; no rain within 4 days; packs 1, 4, 20 L.
  3. Birla Opus product pages: AllDry Wall Fix 4 (4-year warranty statement, FAQ on interiors) and AllDry Salt Seal (for mild efflorescence; warranty registration within 15 days).
  4. Birla Opus, Calista Ever Wash Shine and Style Power Bright sheets: 130–150 and 50–60 sq ft/L for 2 coats; 4–6 h between coats.
  5. Birla White, ActivCoat Interior primer: 1:1 with water, 170–200 sq ft/L per coat on putty; WallSeal Waterproof putty: water-resistant white cement putty.
  6. Plastic sheet test: usual practice among painters, not a maker's figure.

Send us a photo of the patch

The patch, the other side of the wall and what is above it. We will tell you which cause it looks like and what to buy, with today's price, on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com