Birla White Seep Guard Vertical in Muzaffarpur: for outside walls that take rain, how much 15 kg covers, and today's price
Seep Guard Vertical goes on the outside face of walls that take rain, and only there. It is a white cement and polymer coating that stops rain soaking through plaster and cracks. It is not for damp that rises from the ground. That wet comes up inside the wall from below, and the product for it is Seep Blocker 2K on the inside face.
Not sure which kind of wet you have? Dampness, seepage and leakage sorts them, and where is the leak coming from gives the tests. Today's price is on the waterproofing rate board.
Check where the water comes from before you buy
Birla White sells Seep Guard Vertical for exterior vertical walls, and its 8-year warranty is for outside use only. So the question is not "is my wall damp" but "is the water coming in from the rain side".
Rain comes in: Seep Guard Vertical
A wall that goes dark after rain, inside patches that appear in the monsoon and dry in winter, hairline cracks on the outside plaster, a parapet or boundary wall. In Bihar the rain usually drives from the east and south-east (usual practice), so look for the wall that stays dark longest after a shower. The coating goes on the outside face.
Damp rises from the ground: Seep Blocker 2K
Wet at the bottom 2–3 feet, white salt (namak) on the plaster, worse in the rains and never fully dry. A coat on the outside does not reach it. Use Seep Blocker 2K on the inside face, after the damaged plaster is taken off.
Roof, parapet top, bathroom: other products
A roof or terrace leak is a roof job: terrace waterproofing. A bathroom leaking into the room below is bathroom waterproofing. A leaking pipe needs the plumber first. Seep Guard Vertical is not for any of these.
A priming coat, then the finish coat, then paint over it
Prepare. Birla White asks for a clean wall: no dust, oil, loose paint or salt, and no cracks, pores or pinholes. Fill cracks first; we use Seal & Dry SBR in the repair mortar. New plaster is fine; so is old plaster after the loose part is chipped off.
Wet the wall before the coat, damp but with no water running (usual practice for cement coatings; Birla White's pack says how long). Mix the priming coat at 1 kg powder to 1 litre of clean water, a smooth slurry. Put the powder into the water slowly, not the water onto the powder.
Finish coat at 650 ml of water per kg, brush or roller. Birla White's FAQ says Seep Guard needs no curing. It does not publish the hours between coats on the pages we could read, so follow the pack; our rule of thumb is to wait until the last coat is firm to the touch and not tacky.
Then paint. Let the wall dry fully, one coat of exterior primer (about 3–4 hours to dry), then exterior emulsion. Birla White's warranty needs this system. Which exterior paint holds in Bihar's rain: exterior paint and rain.
Birla White's figures depend on how many coats. Plan on the lower one.
The product page lists 1.30–1.48 sq m per kg, which is 14–16 sq ft per kg, for one priming coat plus two finish coats on a good surface. A trade listing of the spec table gives 24–26 sq ft per kg for the priming coat plus one finish coat on plaster, and about 14–16 again for three coats on concrete. The warranty card asks for not less than 2.32 sq m per kg (about 25 sq ft per kg) when registering.
So a 15 kg bag covers about 210–240 sq ft for three coats, or 360–390 sq ft for two. We plan the bags on 14 sq ft per kg for a rough, old or concrete wall, and 24 for smooth plaster. A wall that drinks more than you planned leaves you a bag short on the scaffold, which costs more than a spare bag.
| Per 15 kg bag | Powder : water | Water per bag |
|---|---|---|
| Priming coat | 1 kg : 1 L (1:1) | up to 15 L |
| Finish coat | 1 kg : 650 ml | up to 9.75 L |
The water column is for a whole bag used for that one coat; in practice the bag is split across the coats, so you mix only what you can brush in about an hour.
The heat claim: Birla White's pages say the coating lowers the surface temperature by 6–8 °C on one page, by up to 10 °C on another, and by 8–10 °C on a third. We treat it as a small bonus, not a reason to buy; the job of this product is keeping rain out.
The pack we keep
One pack on our shelf. Today's price, with GST on the bill, is on the
Prices are from our latest bill and change often. Please confirm today's rate on WhatsApp or call before buying.
waterproofing rate board.Birla White also makes Seep Guard for horizontal surfaces (roofs, ledges) and for interior surfaces. They are separate products with their own packs. Ask us on WhatsApp and we will order it and tell you the time it takes. Seep Guard Vertical is a single-pack powder; unopened, keep it dry and off the floor.
The 8-year warranty: what it needs
Birla White's page says 8 years, and its warranty guide sets the conditions. Four things matter to a house owner.
Outside walls only
The warranty covers exterior use. The coating can go on other vertical surfaces, but the 8 years does not follow it there.
The whole system
Seep Guard Vertical, one coat of exterior primer, exterior emulsion. Skip the paint and you have not done the system the card describes.
A clean, sound wall
No cracks, pores or pinholes left, no dust, oil or old loose paint. Fill and clean before the first coat.
Register it
Birla White has an online registration with the warranty guide. Keep our GST bill and the pack. Steps: how to register the warranty.
Measure the rain-facing walls only
Wall area: 260 sq ft. Add all the rain-facing sides together if there is more than one.
You need
Also plan exterior primer and exterior emulsion for the same area; the warranty system needs them.
Short answers
What is the Seep Guard Vertical 15 kg price in Muzaffarpur?
Our price for the day is on the waterproofing rate board, with GST on the bill. Shop prices change with the day and the carriage, so we do not quote one from memory. A 15 kg bag covers about 210–390 sq ft depending on the coats.
Can I use Seep Guard Vertical for damp rising from the ground?
No. It is for the outside face of walls that take rain. Damp rising from the ground needs Seep Blocker 2K on the inside face. A coat outside a wall with ground damp can push the wet higher.
How much does a 15 kg bag of Seep Guard Vertical cover?
About 210–240 sq ft for a priming coat plus two finish coats (14–16 sq ft per kg), and 360–390 sq ft for a priming coat plus one finish coat on smooth plaster (24–26 sq ft per kg). We plan on the lower figure for a rough wall.
How much water do I mix with it?
Priming coat: 1 kg powder to 1 litre of clean water. Finish coats: 650 ml of water per kg. Add the powder to the water slowly and mix only what you can brush in about an hour.
Do I need to cure it with water?
Birla White's FAQ says Seep Guard needs no curing. The plaster under it should be sound and the wall dry before the primer and emulsion go on.
Can I put paint over it, and which?
Yes, and for the 8-year warranty you must: one coat of exterior primer, then exterior emulsion. See exterior paint and rain.
Is the 8-year warranty for inside walls too?
No. Birla White's warranty is for exterior use. For inside walls with a ground-damp problem, see Seep Blocker 2K.
Does it cool the house?
Birla White's pages claim a surface temperature drop (6–8 °C, up to 10 °C and 8–10 °C on different pages). Treat it as a small bonus. Its main job is keeping rain out of the wall.
How do I know if the leak is rain or something else?
Read where is the leak coming from and dampness, seepage and leakage. Or send us a photo on WhatsApp.
Paint Engineer at our Reva Road store, Muzaffarpur. The figures here are Birla White's own, read on 13 Nov 2026. Where its pages disagree, this page says so and takes the safer figure.
Where the numbers come from
- Birla White, Seep Guard Vertical Surfaces page: white cement and German polymers, exterior walls, 8-year warranty, up to 5 bar water pressure; its FAQ lists coverage of 1.30–1.48 sq m per kg for a priming coat and two finish coats, and no curing.
- Birla White, Understanding the different types of Seep Guard: Vertical is for exterior vertical walls; priming coat 1,000 ml water per kg, finish coats 650 ml per kg.
- Birla White, Vertical surfaces warranty card: system of Seep Guard Vertical, one coat of exterior primer and exterior emulsion; priming mix 1:1; at least 2.32 sq m per kg for registration.
- Trade listing of the Seep Guard Vertical spec table (McCoyMart): 24–26 sq ft per kg for a priming coat plus one coat on plaster, 14–16 for three coats on concrete. A retailer's copy, shown for comparison.
- Birla White, Shield your exterior walls against monsoon rains and its other Seep Guard blogs: brush or roller, UV resistant; temperature drop given as 6–8 °C, up to 10 °C and 8–10 °C on different pages.
- Dr. Fixit, External wall waterproofing FAQs: used for what an exterior coating is for and why rain, drainage and rising damp must be told apart first.
- Store facts: our own shelf at Rewa Road; Seep Guard and Seep Blocker use as set by our store. Methods marked "usual practice" are site practice, not a maker's figure.
Send us a photo of the wall
Tell us which side the rain hits and where the wet shows. We will say which product, how many bags, and today's price, on WhatsApp.