हिंदी Call90310 74624
Home›Problems›Plumbing
Problem · weak tap or shower

Low water pressure in the bathroom or on the top floor: six causes, in the order to check them

The short answer

In a house fed from a roof tank, a weak tap is almost always a plumbing problem, not a missing pump. Check these six in this order. Four of them cost nothing to check. Think about a booster pump only after all six.

  1. Tank low, or the pump not filling it2 min · free
  2. Tank too little above the tapa tape · free
  3. Down-line too thin, too many elbowslook · free
  4. Aerator or shower choked with iron10 min · free
  5. A valve left half closed1 min · free
  6. Old GI pipe scaled insidelook · repipe
0.1
kg/cm² per metreEach metre the tank's water stands above a tap gives it this much push. Tank size adds nothing.
0.5 bar
Jaquar's minimumFor its concealed stop cock. That needs about 5 m of height.
≈ 1.8 m
Top-floor showerUnder a tank on the same roof. About 0.18 kg/cm²: a weak shower.
Why the top floor is always weakest
Height of water above each tap in a two-storey house A two-storey house with a tank on the roof. The water in the tank stands 1.8 m above the top-floor shower, 4.8 m above the ground-floor shower and 6.3 m above the ground-floor bucket tap, giving about 0.18, 0.48 and 0.63 kg/cm². A dashed line 5 m below the water marks Jaquar's 0.5 bar minimum. water in the tank 1.8 m 4.8 m 6.3 m TOP-FLOOR SHOWER 1.8 m below the water 0.18 kg/cm² · weak GROUND-FLOOR SHOWER 4.8 m · about 0.48 · just about 5 m below water = 0.5 bar (Jaquar) BUCKET TAP 6.3 m · about 0.63 · good valve
To scale: 10 ft (3 m) floors, tank on a low pad on the roof, half full. Pipes take a little more away, more with thin pipe and many elbows. 10 m of water height = 1 kg/cm² (about 1 bar): standard figure. 0.5 bar: Jaquar data sheet.
Start here · 2 minutes

First, find out which taps are weak

Open the taps one at a time, with everything else shut. Where the weakness is tells you which checks to start with.

Every tap in the house is weak

The trouble is at the source: the tank, the valve at the tank, or the main down-line.

Only the top floor is weak

Downstairs is fine, upstairs trickles. That is height. Pipe size makes it worse.

One tap or one shower only

The fault is at that outlet: its aerator, its shower plate, or its own small valve.

Write it down: the bucket test. Put one bucket under each tap in turn, only that tap open, and count the seconds until it is full. The slow tap shows where to look. Send the seconds with photos on WhatsApp and we can tell you more than "pressure is low".
The six checks

How to check each one, and what fixes it

In this order, because the first ones are the quickest and the most common. Stop when you find the cause.

from pump overflow: runs onlywhen the tank is full air in the line ALMOST EMPTY sludge chokes the outlet
1

The tank is low, or the pump is not filling it

Every tap weak · 2 minutes · free

How to check

  • Go up and look inside the tank. With only a hand's depth of water over the outlet, flow is weak and the taps spit air.
  • Run the pump. Water should start falling into the tank within a minute or two. When the tank is full, the overflow pipe runs: that is your sign the tank fills.
  • Look at the bottom near the outlet. Sand and brown iron sludge settle there and can choke the outlet nipple.

What fixes it

  • Pump runs but no water reaches the tank: see pump not lifting water.
  • Clean the tank through the washout at the bottom. Where the water carries iron, usual practice is twice a year.
  • After the tank has run dry, air stays trapped in the pipes. Open the lowest tap in the house fully until the water runs steady, with no spitting.

Tank outlet and washout fittings: tank nipple · union · how the four openings should be: overhead tank setup

1.8 m · 0.18 tank on the roof 5 ft stand 3.3 m · 0.33 same tank, raised
2

The tank stands too little above the tap

Top floor weak · a measuring tape · free

Water from a roof tank is pushed only by its own height. Every metre between the water in the tank and the tap gives about 0.1 kg/cm². A bigger tank does not help: it only lasts longer.

How to check

  • Measure from the water level in the tank down to the shower head or tap. Floor-to-floor is usually about 10 ft (3 m), so you can count floors. Or use the height check below.
  • A top-floor shower under a tank on the same roof gets only about 1.8 m: about 0.18 kg/cm². Jaquar's data sheet for its concealed stop cock asks for at least 0.5 bar, which is about 5 m.

What fixes it

  • Raise the tank on a stand. Each foot adds about 0.03 kg/cm². A 5 ft stand takes that top-floor shower from 0.18 to about 0.33. Taps and a hand shower feel it at once. An overhead rain shower will still be on the weak side.
  • A full 1,000 litre tank weighs about a tonne (a litre of water is a kilo). The stand must stand on a beam or wall line, not in the middle of the slab. Send us photos of the roof on WhatsApp before you build it.
  • Building another floor later? The tank goes up then anyway. Plan the stand with it.
  • Still too weak for the shower you want? That is the one case where a booster pump earns its place.
½ INCH, 9 ELBOWS 1 INCH, 2 BENDS trickle
3

The down-line is too thin or has too many elbows

Every tap or top floor · look · free to check

How to check

  • Read the size printed on the pipe leaving the tank. In ASTM sizes, ½ inch is about 21 mm across the outside and 1 inch about 33 mm. A ½ inch line feeding a whole floor is too thin.
  • Telltale sign: one tap runs fine, but when a second opens or the cistern refills, both go weak.
  • Count the elbows between the tank and the bathroom. Standard engineering tables count each sharp 90° elbow as about 30 pipe-widths of straight pipe: about 0.75 m of 1 inch pipe. Ten elbows behave like 7 to 8 m of extra pipe.

What fixes it

  • Relay the main run as a 1 inch down-line (1½ inch for a bigger house), with a ¾ inch branch into each bathroom. Use ½ inch only for the last short run to each tap. See the drawing below.
  • Fewer turns: go straight, and use a long bend where a turn is needed.
  • The open run across the roof and down the outside wall is usually the easy part to replace, and it is where most of the loss is.

Buy: 1 inch UPVC pipe · ¾ inch pipe · reducer 40×25 · reducing tee 25×15 · elbows · PVC solvent

iron crust on the mesh vinegar, 1 hour aerator
4

The aerator or shower is choked with iron

One tap weak · 10 minutes · free

Groundwater in much of north Bihar carries iron. The state's Economic Survey 2024-25 counts 21,709 rural wards with high iron. It settles as an orange crust on the fine mesh at the mouth of a tap and in the small holes of a shower plate.

How to check

  • Unscrew the aerator, the small cap at the tap's mouth, by hand or with pliers over a cloth. Open the tap. If water now gushes, you have found it.
  • Shower: the holes are crusted orange or white, or the spray shoots sideways.
  • New tap fitted after plumbing work? Sand and pipe shavings sit in the aerator. Clean it in the first week.

What fixes it

  • Soak the aerator or shower plate in white vinegar or lemon water for about an hour. Scrub with an old toothbrush, rinse, screw it back.
  • Don't widen the holes with a pin, and keep toilet acid off chrome.
  • Choking again every month? The iron is coming in with every tank-fill. An iron filter at the tank inlet is the real fix: see iron stains on sanitaryware.
Handle along the pipe = fully open OPENHALFSHUT full flowweak, and youwon't noticeno water
5

A valve has been left half closed

Any tap · 1 minute · free

How to check

  • Ball valve at the tank outlet: the handle should lie along the pipe. Anything at an angle is half open.
  • Concealed stop cock in the bathroom wall, above the mixer: turn it fully anticlockwise. Plumbers often leave it part-closed after tiling.
  • Angle valves under the basin and behind the WC, and any old round-wheel gate valve: turn anticlockwise until it stops.

What fixes it

  • Open it fully. If the handle is stiff, or water weeps at the stem, replace the valve. Don't leave it half-stuck.
  • Usual practice: a ball valve at the tank outlet, so a tap can be repaired without draining the tank. It is the most useful single fitting on the roof.

Buy: Prince UPVC ball valve 1½ inch · angle valve and connection pipe · Teflon tape

OLD GI rust narrows the bore UPVC smooth, stays open
6

An old GI line is scaled up inside

Every tap, getting worse over years · repipe

How to check

  • Older house, grey metal pipes with threaded joints, rusty water for the first few seconds in the morning, and pressure that has dropped slowly over the years.
  • When a joint near the tank is opened, look inside the pipe: a rough brown crust where the bore should be round and clean.

What fixes it

  • Cleaning does not bring a scaled GI pipe back. Replace it: UPVC for cold water, CPVC for the geyser line. Prince says UPVC's smooth bore resists scale and loses less to friction. Birla Nu notes that even 1 mm of scale inside a pipe cuts flow noticeably.
  • Start with the main down-line from the tank, which is open and quick. Change the hidden branches when the bathroom is next redone.

Buy: UPVC pipes and fittings · MTA/FTA to join onto old threads · why GI is on its way out: GI pipes and fittings

Check 2, worked out for you

How much push can your tap get from the tank?

Tell us where the tank sits and where the tap is. This gives the most the height can give. Thin pipe and elbows take some of it away.

Assumes the tank sits on a low pad and is half full, so the water stands about 0.9 m above the roof. Figures: 10 m of water = 1 kg/cm², about 1 bar.

Your tap

—height of water above it
—kg/cm², at most
00.2 weak0.5 Jaquar min.1.0

—

Ask us about this tap on WhatsApp

This is the push from height alone, before pipe losses. If your tap is far weaker than this number, the cause is in checks 1, 3, 4, 5 or 6, not the height.

Check 3, done right

Pipe sizes from the tank to the tap

Big at the top, smaller as each branch feeds fewer taps. This is the usual layout, with the fittings we keep at each joint.

Pipe sizes from the roof tank to the taps From the tank: 1 1/2 inch tank nipple, 1 1/2 inch ball valve, reducer to 1 inch, 1 inch down-line through both floors, a 3/4 inch branch into each bathroom, and 1/2 inch only for the last short runs to the shower, basin and cistern. showerbasincisternshowerbasincistern TOP FLOORGROUND FLOOR 1 2 3 4 5 6 1½ inch 1 inch ¾ inch ½ inch Pipe drawn thicker = bigger size. ½ inch only for the last metre or two.
Usual practice for a house fed from a roof tank. Fewer elbows on the 1 inch run means more push at every floor.
  1. Tank nipple, 1½ inchThe outlet through the tank wall, a little above the bottom so sludge stays behind. Tank nipple
  2. Ball valve, 1½ inchRight after the tank, so the house can be shut off without draining it. Prince ball valve
  3. Reducer 40×25Steps from 1½ inch down to the 1 inch down-line. Reducer and bush
  4. Down-line, 1 inchThrough every floor. Go 1½ inch for a bigger house or three or more bathrooms. 1 inch UPVC · 1½ inch
  5. Branch, ¾ inchOne into each bathroom and the kitchen, taken off with a reducing tee. ¾ inch pipe · tees
  6. ½ inch to each outletShower, basin, cistern. Use an FT elbow with a brass insert behind each tap. ½ inch pipe · elbows

The full guide, with what changes for a far bathroom or a low tank: pipe size from tank to bathroom.

Only after the six checks

Searching for a "pressure pump for home"? Read this first

A booster pump sits on the line from the tank and pushes harder whenever a tap opens. It adds push. It cannot add water, and it cannot open up a choked pipe.

When a booster is the right answer

  • A top-floor bathroom right under the tank, and the height check gives well under 0.5 kg/cm².
  • You have done checks 1, 3, 4, 5 and 6, and the tank can't go higher.
  • An instant geyser that won't start because the flow is too weak. Its manual gives the minimum pressure.

When it won't help

  • The tank runs dry. A booster on an empty tank runs dry and burns out.
  • The line is ½ inch or scaled GI. A pump on a narrow pipe is still a narrow pipe.
  • The weakness is one tap. That is an aerator or a valve.

How to fit it properly

  • On its own line from the tank to that bathroom only. The rest of the house stays on gravity.
  • A bypass with a non-return valve, so water still comes during a power cut.
  • Dry-run cut-off, so the pump stops when the tank is low. Crompton's Mini Force I booster, for one, has a float switch for this.
  • Its own switch, MCB and earth, with wire sized for the motor: wire size for a motor.
How a booster pump is fitted for one top-floor bathroom The roof tank keeps feeding the rest of the house by gravity. A second outlet runs to a small booster pump on the roof, then down to the top-floor shower. A bypass pipe with a non-return valve goes round the pump. A float in the tank cuts the pump off when water is low. The pump has its own switch, MCB and earth. float: dry-run cut-off rest of the house: gravity, as before PUMP bypass + non-return valve: water still comes in a power cut TOP-FLOOR BATHROOM ONLY pump starts when the tap opens MCB + earth
One way to do it: only the weak bathroom gets the pump. Never fit an ordinary motor in the line without a pressure or flow switch; it will run with no tap open.

What we can do: we can order a booster pump for you; ask on WhatsApp for the time it takes. Send photos of the tank, the roof and the weak bathroom first. If raising the tank or a 1 inch down-line will do the job, we will tell you that instead. Our Nova 0.5 HP and 1 HP pumps are self-priming pumps that fill the tank from the boring. They are not boosters. For a house going up a floor, see pump for a 2-storey house.

Questions people ask us

Short answers

Will a bigger tank give more pressure?

No. The push at a tap comes from how high the water in the tank stands above it, not from how much water the tank holds. Every metre of height gives about 0.1 kg/cm². A bigger tank only lasts longer between fills.

Will a pressure pump fix low water pressure at home?

Only when the tank stands too little above the tap, which is the usual case for a top-floor bathroom under a tank on the same roof. If the tank runs dry, the down-line is too thin, a valve is half shut, the aerator is choked or old GI pipe is scaled inside, a booster pump won't cure it. Do the six checks first.

Why is pressure good downstairs but weak upstairs?

Because the ground floor sits about 3 m further below the tank. In a two-storey house with the tank on the roof, a ground-floor shower gets about 4.8 m of height (about 0.48 kg/cm²). A first-floor shower gets only about 1.8 m (about 0.18).

Why does the shower go weak when someone flushes?

The pipe feeding both is too thin for two outlets at once. Usually a ½ inch line is doing the job of a 1 inch down-line, or a long run has many elbows. The fix is a 1 inch down-line from the tank with a ¾ inch branch into each bathroom (check 3).

What pipe size should go from the tank to the bathroom?

Usual practice: a 1½ inch tank nipple and ball valve at the tank, a 1 inch down-line (1½ inch for a bigger house), a ¾ inch branch into each bathroom and the kitchen, and ½ inch only for the last short run to each tap, cistern and basin. Details: pipe size guide.

How do I check the pressure without a gauge?

Do the bucket test. Time how long one bucket takes to fill at each tap, with only that tap open, and write the seconds down. The tap that takes far longer than the others shows where to look. Send us the numbers on WhatsApp with photos.

Paani ka pressure kam hai, motor lagwaun? (Should I fit a motor?)

The motor you already have fills the tank. It does not raise pressure at the taps. If the tank fills, do the six checks above. Only a top-floor bathroom with too little height needs a booster, fitted on its own line with a dry-run cut-off.

My instant geyser won't start on the top floor. Why?

Instant geysers switch on only above a certain flow, and a top-floor line under a roof tank often doesn't reach it. The geyser's manual gives its minimum pressure. A storage geyser works on lower pressure. Otherwise raise the tank, or fit a booster for that bathroom.

Arun Tiwari
Experienced thekedar, Tashya Ventures

Answers site and plumbing questions at our Reva Road store, Muzaffarpur. The six checks are in the order a plumber should follow on site, quickest first. Maker figures were checked against each maker's own sheet on 12 Nov 2026. Figures that are plain physics or standard engineering are labelled as such.

Where the numbers come from

  1. Standard figure (hydrostatics): 10 m of water height = 1 kg/cm² ≈ 0.98 bar, so 1 m ≈ 0.1 kg/cm². A litre of water weighs 1 kg.
  2. Jaquar, data sheet for ALD-CHR-069FT concealed stop cock body (15 mm line): recommended pressure 0.5–5 bar; flow 47 L/min at 3 bar.
  3. Standard figure: equivalent length of a standard 90° elbow ≈ 30 pipe diameters (Crane Technical Paper 410, the usual engineering reference).
  4. ASTM outside diameters used by Prince Easyfit and Ashirvad UPVC: ½ inch 21.3 mm, ¾ inch 26.7 mm, 1 inch 33.4 mm, 1½ inch 48.3 mm.
  5. Prince Pipes, Best pipe for water supply in homes: UPVC's smooth bore means lower friction loss and resistance to scale.
  6. Birla Nu, How pipe quality impacts water pressure: a 1 mm loss of internal diameter to scale or corrosion can significantly cut flow.
  7. Crompton, Mini Force I pressure booster pump: 1 HP, maximum lifting height 42 m, 960–3000 L/h, float switch for dry-run protection.
  8. Government of Bihar, Economic Survey 2024-25, as reported by Patna Press: 21,709 rural wards with high iron in groundwater.
  9. Pipe layout (1½ → 1 → ¾ → ½ inch), stand weight and tank cleaning: usual practice, labelled on the page.

Still weak after the six checks?

Send photos of the tank, the pipe leaving it and the weak tap, with your bucket-test seconds. We'll tell you what to change and send the list with today's price.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com