हिंदी Call90310 74624
Home›Guides›Pipes and plumbing
Plumbing · before dhalai

Pipe holes in the slab before dhalai: sleeves for the 110 mm stack, the down-line and the floor traps, so nothing is drilled later

The short answer

Every pipe that will ever cross the slab needs a hole cast into it on dhalai day. The hole is made with a sleeve: a short piece of SWR pipe, one size bigger than the pipe it will carry, tied to the steel and capped before the concrete comes.

  1. 1Toilet stack, 110 mm: a 160 mm sleeve, for each stack, in every slab it passes, roof included (it must vent above the roof).
  2. 2Tank down-line and pump line: a 75 mm sleeve each, in every slab between the pump and the tank and the taps.
  3. 3Upstairs bathroom: a sunken slab, 250–450 mm deep, so the traps sit in the floor. Without a sunk, a sleeve under the WC, the floor trap and the basin.
  4. 4Geyser or solar line, balcony or kitchen drain, rain outlets: one each, where they cross.

Choose the WC and fix the bathroom layout before the shuttering goes up. That decides where every hole goes.

160 mm
Sleeve for a 110 mm stackAbout 20 mm gap all round to pack later.
75 mm
Sleeve for ½″ to 1¼″ linesDown-line, pump line, geyser line.
+50 mm
Sleeve top above the slabCapped, tied, never through a beam.
Where the holes go in a G+1 house
Section of a two-storey house showing every pipe sleeve A ground floor and a first floor, with a roof slab above. A grey 110 mm toilet stack runs up the right side from a chamber in the ground, through sleeve A in the first-floor slab and sleeve B in the roof slab, to a vent cowl above the roof. The upstairs bathroom has a sunken slab with a WC on the filling; its drain leaves through sleeve D in the side of the sunk into the stack. A blue down-line runs from the roof tank through sleeve C in the roof slab to the bathroom taps. A rain outlet E passes through the parapet at the left. chamber TANK A B C D E vent above the roof sunken slab 250–450 mm deep down-line first floor ground floor
Not to scale. Yellow = sleeve. A and B carry the 110 mm stack (160 mm sleeves), C the tank down-line (75 mm), D the bathroom drain out of the sunk, E the rain outlet. The pump line up to the tank needs its own sleeve in each slab too.
Step 1 · the list

Which holes your slab needs

Walk the house in your head, floor by floor, and ask of every pipe: does it cross this slab? If yes, it needs a sleeve in it, and the place is fixed by the walls and fittings above and below. Most houses in Muzaffarpur have the same handful.

Sunken bathroom or flat slab?

An upstairs bathroom is either cast sunken (the slab under it drops 250–450 mm, the traps and drains lie in that box and are filled over), or cast flat with every drain going straight down through the slab and running under the ceiling of the room below. The choice is made now and cannot be changed after dhalai.

With a sunk, the floor of the box gets no holes at all: that is the point of it. The only sleeves are where the drain leaves the box for the stack (D in the drawing), or the stack itself if it rises inside the bathroom. With a flat slab you need a sleeve under the WC outlet, the floor trap and the basin waste, and the pipes show in the room below unless it gets a false ceiling. On our sites the sunk is the usual choice for a house; a flat slab suits a bathroom over a store or a staircase.

Where the stack goes

Keep the 110 mm stack on an outside wall or in a shaft, never through a bedroom. If the ground-floor toilet comes now and the upper one later, put the upper bathroom right over the lower one so one stack serves both: two toilets on one line. Then the first-floor slab needs only the one stack sleeve, and the roof slab one more for the vent.

The lines people forget

The pump line from the boring or sump up to the roof tank crosses every slab. So does a geyser or solar line fed from the roof. A washing-machine or kitchen drain upstairs, and the rain outlets through the parapet, are the others. The rain outlet goes at the lowest point of the roof slope, as on the chhat dhalai checklist.

Two bathrooms, seen from above
Sleeve positions for a sunken bathroom and a flat-slab bathroom Left: a sunken bathroom, the shaded sunk with no holes in its floor; a 160 mm stack sleeve in the slab outside its corner, a drain outlet sleeve in the side of the sunk and a 75 mm down-line sleeve. Right: a flat-slab bathroom with four sleeves: WC outlet at 220 or 300 mm plus tile and plaster from the wall, floor trap, basin waste and stack, with pipes dashed below the slab. SUNKEN · 2–3 holes FLAT SLAB · 4–5 holes SUNKno holes inits floor stack 160 · outlet in sunk side down-line 75 (top right) WC trap basin 220/300 + tile WC 160 · trap 110 · basin 75 stack 160 · pipes run below (dashed)
Usual practice. With a flat slab the WC sleeve sits 220 or 300 mm from the finished wall (by the WC you buy) plus the tile and plaster: 220 or 300 mm toilet.
Step 2 · sizes

How big each sleeve should be

Rule: the sleeve's bore should be at least 25 mm more than the pipe's outside, so there is about 12 mm or more all round to push mortar in later (usual practice). Use a piece of SWR pipe as the sleeve; it is cheap, round and does not rot.

Pipe that will passSleeveGap all round
110 mm toilet stack or WC drain160 mm SWRbore about 151 mmabout 20 mm
75 mm floor-trap or washing-machine drain110 mm SWRbore about 103 mmabout 14 mm
½″, ¾″, 1″, 1¼″ supplydown-line, pump line, geyser line75 mm SWRbore about 70 mm14–24 mm
1½″ or 2″ supply110 mm SWR21–27 mm
40 mm basin waste (flat slab)75 mm SWRabout 15 mm

Bores worked out from the makers' wall thickness: a 160 mm SWR pipe has a 4.0–4.6 mm wall (Type B) and a 110 mm one 3.2–3.8 mm. The supply pipe sizes are Prince Easyfit's outsides: 1″ is 33.4 mm and 1½″ is 48.3 mm. A 50 mm sleeve round a 1″ line leaves only about 6 mm, too thin to pack, so we don't use it for supply lines.

Length of each piece: slab thickness plus about 50 mm standing above the top, so about 200 mm for a usual 125–150 mm slab (usual practice). Five or six sleeves come out of one short offcut.

Pipe inside sleeve, to scale
Four pipe-in-sleeve pairs drawn to scale A 110 mm pipe in a 160 mm sleeve with about 20 mm gap; a 75 mm pipe in a 110 mm sleeve with about 14 mm; a 1 inch pipe in a 75 mm sleeve with about 18 mm; and, crossed out, a 1 inch pipe in a 50 mm sleeve with only about 6 mm. 110160 sleeve≈20 mm gap 75110 sleeve≈14 mm gap 1″ in 75≈18 mm 1″ in 50≈6 mm: too tight
Drawn at 0.8 px per mm. Yellow ring = sleeve wall, grey = SWR pipe, blue = UPVC supply pipe.
Step 3 · the sunk

How deep to sink the bathroom slab

The sunk must be deep enough for the deepest trap plus the fall of its drain to the outlet, plus the screed on top. 250–450 mm covers most houses (usual practice). A western WC with its S-trap built in needs the least; an Orissa pan sitting on its P-trap needs the most. Which WC is the first thing to decide: Orissa pan or western, then S-trap or P-trap.

Add upHow to get it
Trap heightFrom the slab to the centre of the trap outlet, measured on the pan, trap and floor trap you will buy. Bring them to site or ask us for the piece.
Fall of the drain1 in 60 over the run from the farthest trap to the outlet: 20 mm for 1.2 m, 40 mm for 2.4 m, 50 mm for 3 m.
Screed and tileAbout 40 mm over the highest pipe (usual practice; Birla White asks at least 20 mm of screed over a pipe).

Example: a trap outlet 200 mm up, a 2.4 m run (40 mm fall) and 40 mm screed come to 280 mm, so the engineer casts a 300 mm sunk. The engineer sets the slab and beam steel for the drop; the sunk's side, where the drain leaves, gets sleeve D at the drain's level.

Waterproofing of the sunk, the 48-hour water test and the filling come later and are on bathroom waterproofing; the WP+200 for the slab concrete is on waterproofing at dhalai.

Step 4 · on the shuttering

Fixing a sleeve so the concrete can't move it

  1. Mark from two walls. Measure each centre from two wall lines below (not from the shuttering edge) and chalk a cross on the plate. For a stack, keep the centre about 100–125 mm off the bare brick face so the pipe clears plaster and a clamp (usual practice).
  2. Fix a stop on the plate. Nail a round wooden disc or a ring of short nails just inside the sleeve's bore, so its bottom can't slide.
  3. Fit between the bars. Slab bars are often closer than a 160 mm sleeve, so one bar may have to be eased aside to the sleeve's edge. Never cut a bar. If one must be cut or moved far, your engineer says what extra steel goes round the hole.
  4. Tie it plumb. Binding wire in an X from the sleeve to the bars on all four sides; check it stands straight with a level.
  5. Cap it. Tape over the top, or stuff it with wet sand and tape, so slurry can't fill it.
  6. Mark it on the plan and photograph it with a tape in the picture, before the concrete comes.
A sleeve ready for concrete
Section through a sleeve tied in the slab shuttering A shuttering plate on props. A wooden disc nailed to the plate holds the bottom of a yellow sleeve. Slab bars run on both sides, one eased aside, with binding wire in an X. Tape caps the top. The concrete line is shown and the sleeve stands about 50 mm above it. top of concrete tape cap ≈50 mm wooden disc nailed bar eased to the edge,not cut wire X
Usual practice. A blank of thermocol wrapped in plastic also leaves a hole, but it must be dug out after and the bare concrete packed; a pipe sleeve stays in and gives a smooth bore.
✓
Step 5 · dhalai day

The check, with the plan in one hand and a tape in the other

Do it the evening before, then once more as the concrete reaches the bathroom.
0 of 9 done
When the shuttering comes off

Look up from below: every sleeve should show a clean round mouth. Poke out any slurry from the top the same week, while it is still soft. Leave the tape on top until the plumber comes.

The rest of slab day (steel, cover, props, curing): chhat dhalai checklist · cement for it: cement for chhat dhalai · the plumbing checks after this one: plumbing checklist by stage

What goes wrong

The four sleeve mistakes, and what to do if a hole was missed

Four sleeve mistakes One: a hole broken with a hammer, cracks round it and a cut bar. Two: a sleeve placed through a beam. Three: a sleeve with no cap, filled with concrete. Four: a sleeve pushed over by the concrete, leaning. Hammeredbar cut, cracks In a beamask the engineer No capfull of concrete Not tiedleans over 1234

1 · A hole broken out later

A hammer and chisel cut the slab steel, crack the concrete round the hole and leave a ragged gap that never seals as well. Most round stains on a ceiling under a bathroom start at a pipe that crossed the slab like this.

2 · A sleeve through a beam

A beam carries the slab; a hole in it is your engineer's decision, not the plumber's. Move the sleeve beside the beam, or let the engineer decide.

3 · No cap

An open sleeve fills with slurry and becomes a plug of concrete inside a plastic ring. Cap every one and check from below when the shuttering comes off.

4 · Not tied

Wet concrete pushes a loose sleeve over. A leaning sleeve means a bent stack or a pipe that rubs on one side, which cannot be packed.

If a hole was missed

Don't let anyone break it. Ask your engineer to mark where the bars and beams are, then have it cut with a diamond core-cutting machine at the size in the table above. The core gives a clean round hole that is packed and sealed the same way as a sleeve. It costs a visit and a day; a hammered hole can cost the ceiling below.

Sealing the sleeves later

The gap round each pipe is packed solid with SBR mortar when the plumbing is done, and the waterproof coat is carried up the pipe. That is step 3 on bathroom waterproofing; it is not repeated here.

Electrical on the same slab

Conduit, fan boxes and round boxes go on the same shuttering the same day, and a slab cast without them cannot be wired later either. Keep the conduits clear of the plumbing sleeves. The electrical list is on conduit before slab casting.

Your slab

Sleeve list maker

Answer for the slab you are casting next. It lists the sleeves with sizes and writes the message to us.

Questions

What people ask before dhalai

What size sleeve for a 110 mm toilet pipe? (latrine pipe ke liye sleeve)

A 160 mm SWR pipe piece. Its bore is about 151 mm, so a 110 mm stack has about 20 mm all round to pack with mortar later. A piece that hugs the pipe leaves a gap too thin to fill.

Why a sleeve, not the pipe cast straight in?

A sleeve gives a clean hole of the right size in the right place. The pipe can be lined up with the walls built later, changed one day, and the gap packed solid. A pipe cast straight in is often off line by the time the walls go up, and the plastic-to-concrete joint opens as the slab moves with heat.

Can the hole be drilled after the slab is cast?

Only with a diamond core-cutting machine, after your engineer marks the bars and beams. Never with a hammer and chisel.

How deep should the sunken bathroom slab be?

Usually 250–450 mm (usual practice). Add the trap height of the pieces you will buy, the drain's fall at 1 in 60 over its run, and about 40 mm of screed. A western WC needs the least, an Orissa pan with its P-trap the most.

Do I need sleeves on the ground floor too?

Not in a slab, but in the plinth: where the toilet drain goes out to the chamber or septic tank, and where the water and pump lines come in. Your engineer decides whether a plinth beam can take the hole.

Will you come to the site to check?

We don't promise site visits. Send photos of the shuttering on WhatsApp the day before dhalai, with a tape in the picture, and we will look at the sleeves with you.

Arun Tiwari
Thekedar · site work, costs and plumbing, Tashya Ventures

Twenty years on sites around Muzaffarpur. He walks the shuttering with the plumber the evening before every dhalai. Pipe and sleeve sizes on this page were checked on 14 Nov 2026 against the makers' tables named below; where a figure is site practice, the page says so. The slab steel, beams and the sunk drop are always your engineer's call.

Where the figures come from

  1. Finolex Pipes, SWR brochure and maker SWR catalogues to IS 13592: 110 mm pipe wall 2.2–2.7 mm (Type A), 3.2–3.8 mm (Type B); 160 mm wall 3.2–3.8 mm (Type A), 4.0–4.6 mm (Type B). Bores on this page are worked out from these.
  2. Prince Easyfit UPVC, made to ASTM D1785, as on our Easyfit Sch 40 and Sch 80 page: 1″ = 33.4 mm and 1½″ = 48.3 mm outside.
  3. Studio Matrx, Bathroom planning for new homes in India: sleeves for the stack and floor traps are cast in at slab casting; sunken slab 250–450 mm. It agrees with our site practice.
  4. Birla White, as set out on our bathroom waterproofing page: at least 20 mm screed over pipes; sleeve packing and the water test.
  5. Drain fall 1 in 60, as on our plumbing checklist (IS 1742 is reported to give 1 in 57 for a 100 mm drain).
  6. Sleeve gap of 12 mm or more, the 50 mm stand-up, 200 mm pieces, stack 100–125 mm off the brick, disc-and-wire fixing, sunk depth range: usual practice on Muzaffarpur sites.

Send us your bathroom plan before the shuttering

Arun will mark every sleeve with its size and send the list with today's price on WhatsApp.

TASHYABUILDING SOLUTIONS · MUZAFFARPUR
WhatsApp 90310 74624tashyaventures.com